American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Double Scrollsaw Blade Life Glendale Heights IL

When the scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood is usually less than 1/2 in. thick. To get more life out of the blade, you can make an auxiliary table that raises the workpiece, so you can cut with the top half of the blade when the bottom half gets dull.

The Home Depot
(630)980-8330
295 E Armytrail Rd
Glendale Heights, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(630)289-6247
950 IL Route 59
Bartlett, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)352-3325
600 Meacham Road
Elk Grove Village, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(630)792-9600
2000 Butterfield Rd
Downers Grove, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(630)637-9200
2920 Audrey Ave
Naperville, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(630)462-8607
475 S Schmale Road
Carol Stream, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(630)261-1240
17w734 22nd Street
Oakbrook Terrace, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)798-8700
100 Barrington Road
Schaumburg, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(708)409-0222
37 W North Ave
Northlake, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #10
(847) 310-0447
Schaumburg Marketplace
Schaumburg, IL

Data Provided by:
Data Provided by:

Double Scrollsaw Blade Life

Double Scrollsaw Blade Life

When my scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood I cut is usually less than 1/2 in. thick. To get more life out of my blade, I made an auxiliary table that raises the workpiece, so I can cut with the top half of the blade when the bottom half gets dull.

I made the table by screwing together pieces of 3/4-in. melamine and 1/2-in. plywood and edge-banding all four sides. I drilled a 7-16-in. hole in the center for the blade and cut a 1/16-in. slot in from the back so I can slip the table on and off without removing the blade. 

I filed slight chamfers on the top of the hole and slot, so they won’t catch on the workpiece. I also widened the slot at the back, so it easily slips around the blade. Cleats glued on the bottom hold the table securely in place on the saw (see photo, below). 

I’ve discovered that it takes less time to install the table than it takes to change a blade, so in addition to saving a few bucks in scrollsaw blades, my table saves time, too. 

Click here to read the rest of the article from American Woodworker