American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Double Scrollsaw Blade Life Granite Falls NC

When the scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood is usually less than 1/2 in. thick. To get more life out of the blade, you can make an auxiliary table that raises the workpiece, so you can cut with the top half of the blade when the bottom half gets dull.

Klingspor’s Woodworking Shop of Hickory
(828) 326-9663
856 21st Street Dr. SE
Hickory, NC

Data Provided by:
Bethlehem Do it Best Hardware
(828) 495-8351
9771 N.c. Hwy 127
Hickory, NC
 
Lowe's
(828) 304-6420
1450 2Nd Street Ne
Hickory, NC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF LENOIR, N. C.
828 726-5246
1201 HICKORY BLVD S.E. LENOIR, NC, 28645
Lenoir, NC
 
Ace Home & Auto Store
(828) 754-4091
101 Mulberry St NW, on the corner of Harper Ave. & Mulberry St
Lenoir, NC
 
The Home Depot
(828)327-9200
1530 8th St Dr SE
Hickory, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Ace Hardware
(828) 322-3492
2310 N Center St
Hickory, NC
 
Lowe's
(828) 726-5246
1201 Hickory Blvd. S.E.
Lenoir, NC
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Lenoir - Auth Hometown
(828) 757-0505
112D Wilkesboro Blvd Se
Lenoir, NC
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:13-18
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:13-18

Lowe's
(828) 304-9063
1550 21St Street Drive S.E.
Hickory, NC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Data Provided by:

Double Scrollsaw Blade Life

Double Scrollsaw Blade Life

When my scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood I cut is usually less than 1/2 in. thick. To get more life out of my blade, I made an auxiliary table that raises the workpiece, so I can cut with the top half of the blade when the bottom half gets dull.

I made the table by screwing together pieces of 3/4-in. melamine and 1/2-in. plywood and edge-banding all four sides. I drilled a 7-16-in. hole in the center for the blade and cut a 1/16-in. slot in from the back so I can slip the table on and off without removing the blade. 

I filed slight chamfers on the top of the hole and slot, so they won’t catch on the workpiece. I also widened the slot at the back, so it easily slips around the blade. Cleats glued on the bottom hold the table securely in place on the saw (see photo, below). 

I’ve discovered that it takes less time to install the table than it takes to change a blade, so in addition to saving a few bucks in scrollsaw blades, my table saves time, too. 

Click here to read the rest of the article from American Woodworker