American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Double Scrollsaw Blade Life Keene NH

When the scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood is usually less than 1/2 in. thick. To get more life out of the blade, you can make an auxiliary table that raises the workpiece, so you can cut with the top half of the blade when the bottom half gets dull.

Jacks True Value Hardware
(603) 352-1517
37 Park Ave.
Keene, NH
 
W W Building Supply
(802) 365-4333
7 Loop Rd
Newfane, VT
 
Rockler Woodworking and Hardware #34
(603) 898-5941
373 S. Broadway
Salem, NH

Data Provided by:
The Home Depot
(603)542-4471
425 Washington St
Claremont, NH
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Goosebay Sawmill & Lumber
(603) 798-5135
83 Dover Road Route 4
Chichester, NH

Data Provided by:
Keene - B
(603) 338-5000
480 West St
Keene, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19

Best Septic
(802) 463-9444
153 Birchview Ext
Westminster, VT
Services Offered
Waste services, porta potty, jetting, portable toilet rentals, septic solutions, locating septic tanks, septic tank repair, septic tank cleaning, septic tank filters, septic tank services, snaking, camera service, septic trouble shooting, hand wash station rentals, septic design, septic installation, septic maintenance
Hours
24/7 Emergency Service

Northland Forest Products, Inc.
(603) 642-3665
16 Church StreetPO Box 369
Kingston, NH

Data Provided by:
Woodcraft - Portsmouth, NH
(603) 433-6116
25 Fox Run Road
Newington, NH

Data Provided by:
East Coast Lbr & Bldg Sply Co
(603) 329-5322
4 Colonial Drive
East Hampstead, NH
 
Data Provided by:

Double Scrollsaw Blade Life

Double Scrollsaw Blade Life

When my scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood I cut is usually less than 1/2 in. thick. To get more life out of my blade, I made an auxiliary table that raises the workpiece, so I can cut with the top half of the blade when the bottom half gets dull.

I made the table by screwing together pieces of 3/4-in. melamine and 1/2-in. plywood and edge-banding all four sides. I drilled a 7-16-in. hole in the center for the blade and cut a 1/16-in. slot in from the back so I can slip the table on and off without removing the blade. 

I filed slight chamfers on the top of the hole and slot, so they won’t catch on the workpiece. I also widened the slot at the back, so it easily slips around the blade. Cleats glued on the bottom hold the table securely in place on the saw (see photo, below). 

I’ve discovered that it takes less time to install the table than it takes to change a blade, so in addition to saving a few bucks in scrollsaw blades, my table saves time, too. 

Click here to read the rest of the article from American Woodworker