American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Double Scrollsaw Blade Life Santa Fe NM

When the scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood is usually less than 1/2 in. thick. To get more life out of the blade, you can make an auxiliary table that raises the workpiece, so you can cut with the top half of the blade when the bottom half gets dull.

The Home Depot
(505)424-9463
952 Richards Ave
Santa Fe, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Santa Fe Place
(505) 424-2600
4250 Cerrillos Rd
Santa Fe, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Ace Hardware
(505) 424-9343
2006 Cerrillos Rd Ste 1
Santa Fe, NM
 
Lowe's Home Improvement Warehouse Of Sante Fe
(505) 819-4080
3458 Zafarano Dr
Santa Fe, NM
 
Baca J L Electric Co
(505) 983-6429
1508 1/2 Agua Fria St
Santa Fe, NM
 
Home Depot
(505) 424-9463
952 Richards Ave
Santa Fe, NM
 
Lowe's
(505) 819-4080
3458 Zafarano Road
Santa Fe, NM
Hours
M-SA 6 am - 9 pm
SU 8 am - 8 pm

Kmart 3301 / Cross Merch
(505) 471-9007
1712 St Michaels Dr
Santa Fe, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Almuina Plasters
(505) 501-0786
2660 Ash St
Santa Fe, NM

Data Provided by:
Santa Fe By Design
(505) 988-4111
1512 Pacheco St Ste D101
Santa Fe, NM
 
Data Provided by:

Double Scrollsaw Blade Life

Double Scrollsaw Blade Life

When my scrollsaw blade gets dull, it’s really only dull on the bottom half, because the wood I cut is usually less than 1/2 in. thick. To get more life out of my blade, I made an auxiliary table that raises the workpiece, so I can cut with the top half of the blade when the bottom half gets dull.

I made the table by screwing together pieces of 3/4-in. melamine and 1/2-in. plywood and edge-banding all four sides. I drilled a 7-16-in. hole in the center for the blade and cut a 1/16-in. slot in from the back so I can slip the table on and off without removing the blade. 

I filed slight chamfers on the top of the hole and slot, so they won’t catch on the workpiece. I also widened the slot at the back, so it easily slips around the blade. Cleats glued on the bottom hold the table securely in place on the saw (see photo, below). 

I’ve discovered that it takes less time to install the table than it takes to change a blade, so in addition to saving a few bucks in scrollsaw blades, my table saves time, too. 

Click here to read the rest of the article from American Woodworker