American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Drawer-Slide Outfeed Table Austell GA

In my garage shop, large tools have to be mobile and storable, so I attached this collapsing outfeed support to my saw. It slides on 100-lb. full-extension drawer slides. Extended, the roller sits 36 in. behind the blade, so I can rip boards as long as 6 ft. I can clamp the arms in any position to support shorter boards.

The Home Depot
(770)732-0184
1000 Thornton Road
Lithia Springs, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)691-2077
1032 Research Center
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)432-9930
2450 Cumberland Pkwy
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)439-0707
145 Depot Drive
Hiram, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)841-5608
2525 Piedmont Road NE
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)438-9678
1200 E W Connector SW
Austell, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(678)567-1161
1062 Richard D Sailors
Powder Springs, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)792-6858
2350 Dallas Hwy
Marietta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)577-8311
7399 Douglas Blvd
Douglasville, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)892-8042
650 Ponce DE Leon
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Drawer-Slide Outfeed Table

Drawer-Slide Outfeed Table

In my garage shop, large tools have to be mobile and storable, so I attached this collapsing outfeed support to my saw. It slides on 100-lb. full-extension drawer slides. Extended, the roller sits 36 in. behind the blade, so I can rip boards as long as 6 ft. I can clamp the arms in any position to support shorter boards. Closed, the roller rests 16 in. behind the blade, so it doesn't interfere with the blade guard assembly or with the miter gauge bar during crosscuts.

The support is built like an inside-out drawer. First I bolted support arms onto the saw's cabinet. I had to extend the left arm to allow tilting the motor. Then I installed the drawer slides and the extension arms. On my saw, 20-in. slides were the longest that would fit. I fastened the extension arms securely with a wide board to minimize racking. I mounted the roller on top, centered behind the blade. To position everything correctly during construction, I clamped the roller flush with the saw table.

Sources

HTC Products Inc., (800) 624-2027
22-in. roller with bracket, #HU-22, $19.

Woodworker's Hardware, (800) 383-0130
www.wwhardware.com
100-lb. full-extension 20-in. drawer slides, #KV8414 B20, $14 a set.


Click here to read the rest of the article from American Woodworker