American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Dust-Free Bandsaw Cabot AR

Dust-free bandsaw works great and it's simple to make and use. The following article has some tips to offer to help you use your own bandsaw. So read on to get more details below.

The Home Depot
(501)941-4350
555 Going Road
Cabot, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 3933 / Cross Merch
(501) 843-2206
W Main Street
Cabot, AR
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Whit Davis Lumber Plus
(501) 982-2156
723 School Dr
Jacksonville, AR
 
LOWE'S OF JACKSONVILLE, AR
501 241-1500
2301 T.P. WHITE DRIVE JACKSONVILLE, AR, 72076
Jacksonville, AR
 
Lowe's
(501) 955-2219
4330 East Mccain Boulevard
North Little Rock, AR
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(501)945-3500
4325 E McCain Blvd
North Little Rock, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Whit Davis Lumber Plus
(501) 843-7009
340 Arena Road
Cabot, AR
 
Lowe's
(501) 241-1500
2301 T. P. White Drive
Jacksonville, AR
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Fastenal- Jacksonville
501-982-2442
617 J.P. Wright Loop Jacksonville, AR, 72076
Jacksonville, AR
 
LOWE'S OF N. LITTLE ROCK, AR
501 955-2219
4330 EAST MCCAIN BOULEVARD NORTH LITTLE ROCK, AR, 72117
North Little Rock, AR
 

Dust-Free Bandsaw

Dust-Free Bandsaw

I replaced my bandsaw’s wimpy 1-1/2-in. dust-collection port with a shop-made shroud that makes bandsawing virtually dust-free. The secret: My shroud’s intake port is much larger (see photo and exploded view, below). Another great feature is that the big hose mounts on the back, so it’s out of the way. 

I built this shroud by improving a similar design I’d seen in an old woodworking magazine. My shroud is mounted on a steel plate that I cut to size with my angle grinder (1/4-in.-thick plywood would also work for the mounting plate). I attached this plate to the saw’s casting, using the same tapped holes that held the original port. On saws without a port, you’ll have to drill and tap a couple holes in the casting.

The shroud’s angled top allows the table to tilt. I sawed the back plywood face to match the profile of the saw. I left the front face as wide as possible. It actually extends inside the door and is cut to fit around the wheel. 

I cut a 4-in.-dia. hole in the back face and installed the sheet-metal duct. Then I attached the faces together with a length of 22-gauge galvanized sheet metal. The lip at the bottom helps keep sawdust in the shroud.

Once the shroud was mounted, I marked and cut the saw’s lower door, so it would close. I was reluctant to alter my saw by cutting the door, but I’m glad I did. This shroud makes bandsawing much cleaner and more enjoyable.


Click here to read the rest of the article from American Woodworker