American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Dust-Free Bandsaw O Fallon MO

Dust-free bandsaw works great and it's simple to make and use. The following article has some tips to offer to help you use your own bandsaw. So read on to get more details below.

The Home Depot
(636)327-0897
1920 Wentzville Pkwy
Wentzville, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)936-9494
3891 Mexico Rd
Saint Charles, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(314)291-5288
11215 St Charles Rock Rd
Bridgeton, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - St. Louis/Maryland Heights
(314) 993-0413
2077 Congressional Drive
St. Louis, MO

Data Provided by:
Lowe's of Lake St. Louis
636-561-5914
6302 Ronald Reagan Drive Lake St. Louis, MO, 63367
Lake St. Louis, MO
 
The Home Depot
(636)922-1281
6190 Mid River Mall Dr
St Peter, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(636)536-0675
390 Thf Boulevard
Chesterfield, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #19
(314) 209-1116
11977 St. Charles-Rock Rd.
St. Louis (Bridgeton), MO

Data Provided by:
The Home Depot
(636)207-8875
13929 Manchester Rd
Ballwin, MO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(636) 561-5914
6302 Ronald Reagan Drive
Lake Saint Louis, MO
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Data Provided by:

Dust-Free Bandsaw

Dust-Free Bandsaw

I replaced my bandsaw’s wimpy 1-1/2-in. dust-collection port with a shop-made shroud that makes bandsawing virtually dust-free. The secret: My shroud’s intake port is much larger (see photo and exploded view, below). Another great feature is that the big hose mounts on the back, so it’s out of the way. 

I built this shroud by improving a similar design I’d seen in an old woodworking magazine. My shroud is mounted on a steel plate that I cut to size with my angle grinder (1/4-in.-thick plywood would also work for the mounting plate). I attached this plate to the saw’s casting, using the same tapped holes that held the original port. On saws without a port, you’ll have to drill and tap a couple holes in the casting.

The shroud’s angled top allows the table to tilt. I sawed the back plywood face to match the profile of the saw. I left the front face as wide as possible. It actually extends inside the door and is cut to fit around the wheel. 

I cut a 4-in.-dia. hole in the back face and installed the sheet-metal duct. Then I attached the faces together with a length of 22-gauge galvanized sheet metal. The lip at the bottom helps keep sawdust in the shroud.

Once the shroud was mounted, I marked and cut the saw’s lower door, so it would close. I was reluctant to alter my saw by cutting the door, but I’m glad I did. This shroud makes bandsawing much cleaner and more enjoyable.


Click here to read the rest of the article from American Woodworker