American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Dust-Free Bandsaw Paradise Valley AZ

Dust-free bandsaw works great and it's simple to make and use. The following article has some tips to offer to help you use your own bandsaw. So read on to get more details below.

The Home Depot
(480)951-8211
9170 E Indian Bend Rd
Scottsdale, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(480)767-9294
9890 N 90th Street
Scottsdale, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(602)493-9600
16803 N Tatum Blvd
Phoenix, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(602)482-2430
2217 East Bell Road
Phoenix, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(602)548-9600
2650 W Thunderbird Rd
Phoenix, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(602)225-0980
3609 E Thomas Rd
Phoenix, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Rockler Woodworking and Hardware
(602) 996-3488
Plus 35 Stores Nationwide!
Phoenix, AZ

Data Provided by:
The Home Depot
(480)991-3738
15499 N Hayden Rd
Scottsdale, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodworkers Source - Store #3
(800) 423-2450
18115 N. Black Canyon Highway
Phoenix, AZ

Data Provided by:
The Home Depot
(480)461-0251
853 N Dobson Road
Mesa, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Data Provided by:

Dust-Free Bandsaw

Dust-Free Bandsaw

I replaced my bandsaw’s wimpy 1-1/2-in. dust-collection port with a shop-made shroud that makes bandsawing virtually dust-free. The secret: My shroud’s intake port is much larger (see photo and exploded view, below). Another great feature is that the big hose mounts on the back, so it’s out of the way. 

I built this shroud by improving a similar design I’d seen in an old woodworking magazine. My shroud is mounted on a steel plate that I cut to size with my angle grinder (1/4-in.-thick plywood would also work for the mounting plate). I attached this plate to the saw’s casting, using the same tapped holes that held the original port. On saws without a port, you’ll have to drill and tap a couple holes in the casting.

The shroud’s angled top allows the table to tilt. I sawed the back plywood face to match the profile of the saw. I left the front face as wide as possible. It actually extends inside the door and is cut to fit around the wheel. 

I cut a 4-in.-dia. hole in the back face and installed the sheet-metal duct. Then I attached the faces together with a length of 22-gauge galvanized sheet metal. The lip at the bottom helps keep sawdust in the shroud.

Once the shroud was mounted, I marked and cut the saw’s lower door, so it would close. I was reluctant to alter my saw by cutting the door, but I’m glad I did. This shroud makes bandsawing much cleaner and more enjoyable.


Click here to read the rest of the article from American Woodworker