American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Economical Through Dovetail Jig Casper WY

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

The Home Depot
(307)472-6505
4900 East 2nd Street
Casper, WY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Bloedorn Lumber Building Mtrls
(307) 234-3545
665 S Walnut
Casper, WY
 
Baileys Ace Hardware
(307) 237-8670
2100 E 2nd St, Second Street & Beverly
Casper, WY
 
Kmart 4736 / Cross Merch
(307) 265-0808
4000 E 2Nd St
Casper, WY
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Wyoming Building Supply
(307) 265-7935
2104 Fairgrounds Rd.
Casper, WY
 
Tool Wh/Trans Equipment & Sup
(307) 235-6641
5103 W Yellowstone Hwy Casper, WY, 82602
Casper, WY
 
Woodworkers Supply
800-645-9292
1108 North Glen Road Casper, WY, 82601
Casper, WY
 
Eastridge Mall
(307) 261-4900
701 Se Wyoming Blvd
Casper, WY
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Murdoch's Ranch & Home Supply
(406) 585-4730
370 Miracle Drive
Evansville, WY
 
The Home Depot
(307)632-2897
1740 Fleischli Pkwy
Cheyenne, WY
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 7:00am-8:00pm

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker