American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Economical Through Dovetail Jig Henderson NV

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

The Home Depot
(702)435-9200
1030 Sunset Road
Henderson, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)837-4300
2200 E Serene Ave
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)871-5035
4750 S Decatur Blvd
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702) 642-2600
1275 W Craig Rd
North Las Vegas, NV
 
The Home Depot
(702)220-4903
4195 S Fort Apache Rd
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)434-1948
6025 South Pecos Road
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)641-9600
1401 S Lamb Blvd
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)270-6446
7015 Arroyo Crossing Pky
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)940-2426
9705 W Charleston Blvd
Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(702)642-2600
1275 W Craig Rd
North Las Vegas, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker