American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Economical Through Dovetail Jig Park Hills MO

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

Holekamp Do it center
(573) 358-3371
317 N Division
Bonne Terre, MO
 
Fastenal- Farmington
573-756-0368
424 N. Washington St Farmington, MO, 63640
Farmington, MO
 
Plummer's Hardware
(573) 756-6001
101 E Liberty
Farmington, MO
 
LOWE'S OF FARMINGTON, MO
573 701-8200
625 WEST KARSCH BOULEVARD FARMINGTON, MO, 63640
Farmington, MO
 
Boyer Do it Best Lumber
(573) 438-5461
208 West High Street
Potosi, MO
 
Lowe's
(573) 701-8200
625 West Karsch Boulevard
Farmington, MO
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Farmington Building Supply Co.
(573) 756-5705
306 East Karsch Blvd.
Farmington, MO
 
ABC Supply Co.,Inc/Farmington
573-431-7076
190 Busenbark Place Farmington, MO, 63640
Farmington, MO
 
Maple Valley Ctr
(573) 760-1502
738 Market St
Farmington, MO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16

Dickey Bub True Value
(573) 436-1177
708 High Street E
Potosi, MO
 

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker