American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Economical Through Dovetail Jig Roswell NM

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

The Home Depot
(575)622-2026
2350 N Main
Roswell, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Broadmoor Ctr
(575) 622-1310
1000 S Main St
Roswell, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-18
Tue:9.5-18
Wed:9.5-18
Thu:9.5-18
Fri:9.5-18
Sat:9.5-18
Sun:12-18
Store Features
Mon:9.5-18
Tue:9.5-18
Wed:9.5-18
Thu:9.5-18
Fri:9.5-18
Sat:9.5-18
Sun:12-18

Roswell Lumber Do it center
(575) 622-7841
200 S Main
Roswell, NM
 
The Home Depot
(505)833-9990
2820 Coors Blvd NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(575)492-9117
900 W Joe Harvey Blvd
Hobbs, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Westlake Ace Hardware
(575) 624-0550
2810 D N Main St
Roswell, NM
 
Kmart 7017 / Cross Merch
(505) 623-7480
1705 S Main St
Roswell, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

The Home Depot
(505)899-1290
10200 Coors Dr NW
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(505)865-0425
1800 Main Street NW
Los Lunas, NM
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(505)344-1900
1220 Renaissance Blvd NE
Albuquerque, NM
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker