American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Economical Through Dovetail Jig Tallahassee FL

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

The Home Depot
(850)350-9001
1490 Capital Circle NW
Tallahassee, FL
Hours
Mon-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

Governor'S Square
(850) 671-6300
1500 Apalachee Pkwy
Tallahassee, FL
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-21
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-21

Fastenal- Tallahassee
850-575-3176
572 A Appleyard Drive Tallahassee, FL, 32304
Tallahassee, FL
 
Capital City Lumber Co Inc
(850) 385-0315
2501 Lonnbladh Road
Tallahassee, FL
 
Lowe's
(850) 386-5022
2121 N.E. Capitol Circle
Tallahassee, FL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(850)422-2777
3200 NE Capital Circle
Tallahassee, FL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 4489 / Cross Merch
(850) 877-6133
1701 Apalachee Pkwy
Tallahassee, FL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

LOWE'S OF NE TALLAHASSEE, FLA.
850 386-5022
2121 NE CAPITOL CIRCLE TALLAHASSEE, FL, 32308
Tallahassee, FL
 
Lowe's
(850) 575-1435
5500 Commonwealth Blvd.
Tallahassee, FL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF N.W. TALLAHASSEE, FL
850 575-1435
5500 COMMONWEALTH BLVD TALLAHASSEE, FL, 32303
Tallahassee, FL
 

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker