American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Economical Through Dovetail Jig Twinsburg OH

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make.

The Home Depot
(330)908-1300
8211 Macedonia Commons
Macedonia, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Cleveland, OH
(440) 232-7979
22745 Rockside Road
Bedford, OH

Data Provided by:
The Home Depot
(216)581-6611
21000 Libby Rd
Maple Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)297-1303
3460 Mayfield Rd
Cleveland Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)741-6123
3355 Steelyard Drive
Cleveland, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)562-6000
18800 N Market Pl Drive
Aurora, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)422-0401
9585 State Route 14
Streetsboro, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)922-3448
325 Howe Ave
Cuyahoga Falls, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(440)895-4420
21669 Center Ridge Rd
Rocky River, OH
Hours
Mon-Thur: 7:00am-9:00pm
Fri-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)670-0988
4066 Medina Rd
Fairlawn, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Economical Through Dovetail Jig

Economical Through Dovetail Jig

 

   

 

Forget worrying about limited dovetail jig capacity. The ChestMate dovetail jig allows cutting through dovetails anywhere on boards of any width. The process is pretty simple. The jig has an indexing pin that fits 1/8-in. kerfs sawn in a story stick that you make: You mark the story stick as you lay out the pin locations on the board and then cut the kerfs. When the story stick is indexed and clamped onto each workpiece, the saw kerfs position the jig for  each socket and pin. The jig has dedicated inserts for cutting the sockets and the pins. You cut the sockets first with a dovetail bit (top photo, at right). Reposition the story stick on the second board to cut the pins (bottom photo). Install a straight bit in your router and the pin insert in the jig. The pin insert allows adjusting the pin width to fit the sockets you've already cut. Once you've dialed in the perfect pin width on a test piece, you're good to go. To orient the joint with half-pins at the ends, instead of half-tails as shown, you'll need a longer story stick with kerfs at the ends of the workpiece. Routing dovetails with this jig is precise, but it isn't very fast, because you have to reposition the jig to cut each socket and pin. For widely-spaced pins, a third routing pass is required to clean out the waste. The ChestMate is designed for use with 3/4-in.-thick stock and routers with 6-in.-dia. bases. Inserts for 14-degree and 7-degree dovetail bits are included with the jig. You supply the router bits and guide bushing.

Source
Prazi USA, www.praziusa.com, (800) 262-0211, ChestMate Dovetail Jig, PR3900, $99.


Click here to read the rest of the article from American Woodworker