American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Eliminate Fuzzy Fillets Appleton WI

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Woodcraft - Fox Cities/Appleton, WI
(920) 730-9663
4731 Michael's Drive
Appleton, WI

Data Provided by:
The Home Depot
(920)993-1123
653 N Westhill Blvd
Grand Chute, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's of Buchanan
920-636-2782
W 3255 Van Roy Rd Appleton, WI, 54915
Appleton, WI
 
Fox River Mall Rr9
(920) 738-8666
4301 W Wisconsin Ave
Appleton, WI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-19
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-19

Northside True Value Hdwe
(920) 734-5944
1415 N Richmond St
Appleton, WI
 
The Home Depot
(920)734-8134
2201 S Kensington Ave
Appleton, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kitz & Pfeil True Value Hdwe
(920) 739-9481
1800 S Lawe St
Appleton, WI
 
Lowe's
(920) 636-2782
W3255 Van Roy Road
Appleton, WI
Hours
M-SA 6:30 am - 9 pm
SU 8 am - 7 pm

Ace Hardware Of Appleton Inc
(920) 731-0500
500 E Northland Ave, Meade and Oneida Streets, next to the "PIG"
Appleton, WI
 
Kitz & Pfeil True Value Hdwe
(920) 722-2877
1212 Appleton Rd
Menasha, WI
 
Data Provided by:

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker