American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Eliminate Fuzzy Fillets Cheyenne WY

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

The Home Depot
(307)632-2897
1740 Fleischli Pkwy
Cheyenne, WY
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 7:00am-8:00pm

Mead Lumber
(307) 635-7928
2222 Bent Ave
Cheyenne, WY
 
Lowe's
(307) 632-3616
9,# 1608 Prairie Avenue
Cheyenne, WY
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Frontier Fashion Mall
(307) 775-6600
1400 Del Range Blvd
Cheyenne, WY
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-21
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-21

Capital Lbr True Value Hdwe
(307) 634-4471
1222 Dunn Ave
Cheyenne, WY
 
Bloedorn Lumber Building Mtrls
(307) 632-0578
1551 Stillwater Ave
Cheyenne, WY
 
Murdoch's Ranch & Home Supply
(307) 632-7888
3773 E Lincoln Way
Cheyenne, WY
 
LOWE'S OF CHEYENNE, WY
307 632-3616
1608 PRAIRIE AVENUE CHEYENNE, WY, 82009
Cheyenne, WY
 
Cheyenne - D
(307) 638-8008
1840 Dell Range Blvd
Cheyenne, WY
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Capital Lbr True Value Hardware
(800) 642-7392
1222 Dunn Ave
Cheyenne, WY

Data Provided by:
Data Provided by:

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker