American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Eliminate Fuzzy Fillets Keene NH

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Jacks True Value Hardware
(603) 352-1517
37 Park Ave.
Keene, NH
 
W W Building Supply
(802) 365-4333
7 Loop Rd
Newfane, VT
 
Northland Forest Products, Inc.
(603) 642-3665
16 Church StreetPO Box 369
Kingston, NH

Data Provided by:
The Home Depot
(603)542-4471
425 Washington St
Claremont, NH
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Woodcraft - Portsmouth, NH
(603) 433-6116
25 Fox Run Road
Newington, NH

Data Provided by:
Keene - B
(603) 338-5000
480 West St
Keene, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19

Best Septic
(802) 463-9444
153 Birchview Ext
Westminster, VT
Services Offered
Waste services, porta potty, jetting, portable toilet rentals, septic solutions, locating septic tanks, septic tank repair, septic tank cleaning, septic tank filters, septic tank services, snaking, camera service, septic trouble shooting, hand wash station rentals, septic design, septic installation, septic maintenance
Hours
24/7 Emergency Service

Goosebay Sawmill & Lumber
(603) 798-5135
83 Dover Road Route 4
Chichester, NH

Data Provided by:
Rockler Woodworking and Hardware #34
(603) 898-5941
373 S. Broadway
Salem, NH

Data Provided by:
Marquis True Value Hardware
(603) 246-3552
Washington St
West Stewartstown, NH
 
Data Provided by:

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker