American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Eliminate Fuzzy Fillets Nashua NH

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Rockler Woodworking and Hardware #34
(603) 898-5941
373 S. Broadway
Salem, NH

Data Provided by:
Woodery Lumber Company
(978) 342-9293
110 Pleasant St
Lunenburg, MA

Data Provided by:
Pheasant Ln Mall
(603) 891-6200
310 Daniel Webster Hwy Ste 102
Nashua, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:8-21
Sun:10-18.5
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:8-21
Sun:10-18.5

Lowe's
(603) 521-9950
143 Daniel Webster Highway
Nashua, NH
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Bridge Street True Value
(603) 635-1521
122 Bridge St
Pelham, NH
 
New England Hardwood Supply Company, Inc.
(978) 486-8683
100 Taylor StPO Box 2254
Littleton, MA

Data Provided by:
Artisan Lumber, Inc.
(781) 431-1500
35 Leominster Road
Lunenburg, MA

Data Provided by:
Nashua - B
(603) 324-0800
375 Amherst St
Nashua, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-18
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:9-21
Sun:10-18

Hudson True Value Hdw.
(603) 883-3100
114 Derry Road
Hudson, NH
 
Lorden True Value Hdwe
(978) 433-2348
53 Main St
Pepperell, MA
 
Data Provided by:

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker