American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Eliminate Fuzzy Fillets Osseo MN

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

The Home Depot
(763)494-0117
15800 Grove Circle North
Maple Grove, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)422-1200
3550 124th Ave NW
Coon Rapids, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)571-9600
5650 Main St, NE
Fridley, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #14
(952) 542-0111
12995 Ridgedale Dr.
Minnetonka, MN

Data Provided by:
The Home Depot
(952)512-0109
5800 Cedar Lake Rd
St Louis Park, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)533-1200
6701 Boone Ave North
Brooklyn Park, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)509-9590
1705 Annapolis Lane
Plymouth, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)795-2060
99 Northtown Drive
Blaine, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(612)782-9594
1520 New Brighton Blvd
Minneapolis, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(763)717-0316
4550 Pheasant Ridge Dr
Blaine, MN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker