American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Eliminate Fuzzy Fillets Palmer AK

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

The Home Depot
(907)357-8181
1255 Palmer Wasilla Hwy
Wasilla, AK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Spenard Builders Supply- Wasilla
907-373-2806
2501 E Bogard Road Wasilla, AK, 99654
Wasilla, AK
 
Weld Air Alaska
(907) 373-2000
301 Centaur Wasilla, AK, 99654
Wasilla, AK
 
Spenard Builders Supply- Big Lake
907-892-6001
10927 Big Lake Road Big Lake, AK, 99652
Big Lake, AK
 
The Home Depot
(907) 563-9800
515 E Tudor RD
Anchorage, AK
 
Wasilla - B
(907) 352-6800
1000 S Seward Meridian Rd
Wasilla, AK
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Alaska Industrial Hardware- Wasilla
907-376-5274
751 West Parks Hwy Wasilla, AK, 99654
Wasilla, AK
 
Lowe's
(907) 352-3100
2561 East Sun Mountain Avenue
Wasilla, AK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(907)357-8181
1255 Palmer Wasilla Hwy
Wasilla, AK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(907)276-2006
400 Rodeo Place
Anchorage, AK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker