American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Eliminate Fuzzy Fillets Spartanburg SC

The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

The Home Depot
(864)574-2922
121 Dorman Center Drive
Spartanburg, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

LOWE'S OF SPARTANBURG, S. C.
864 576-7744
100 PEACHWOOD CENTRE DR SPARTANBURG, SC, 29301
Spartanburg, SC
 
Westgate Mall
(864) 587-5300
205 W Blackstock Rd Ste C
Spartanburg, SC
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18

Fastenal- Spartanburg
864-948-9600
67 Dexter Rd Spartanburg, SC, 29303
Spartanburg, SC
 
Ace Hardware
(864) 578-7008
3433 Boiling Springs Road
Spartanburg, SC
 
The Home Depot
(864)579-0382
2300 E Main Street
Spartanburg, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(864) 216-4934
120 East Blackstock Road
Spartanburg, SC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Blue Eagle Equipment
864-583-0700
350 TNS Road Spartanburg, SC, 29303
Spartanburg, SC
 
LOWE'S OF BOILING SPRINGS, SC
864 573-2771
170 RAINBOW LAKE ROAD BOILING SPRINGS, SC, 29316
Boiling Springs, SC
 
Lowe's
(864) 573-2771
170 Rainbow Lake Road
Boiling Springs, SC
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Eliminate Fuzzy Fillets

Eliminate Fuzzy Fillets

   

Freud's new Quadra-Cut router bits produce routed profiles with little or no tear out or fuzz even on cross-grain cuts. These unique, patented bits employ four cutting edges instead of two. The large profile cutters remove most of the stock with an upshear cut. Then a pair of downshear cutters makes the final cut to produce an ultra clean edge with no fuzz or splinters at the top surface. Freud is introducing the new Quadra-Cut technology in select edge-forming bits with 1⁄2-in. shanks. We got our hands on a round-over bit and tried it out on some red oak panels. The results were amazing (see photos above). Both bits were brand new, but the difference in cut quality, especially at the fillet on the top, was quite noticeable. We made full-profile cuts in a single pass to really put the design to the test. The Quadra-Cut bit left a near-perfect surface requiring only a light sanding before finishing (Photo A). A standard bit of the same profile left a lot of fuzz and tearout at the top of the fillet (Photo B). Needless to say, we were very impressed with this bit design.

Source
Freud, www.freudtools.com 

Click here to read the rest of the article from American Woodworker