American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Fast Accurate Height Adjustments Cabot AR

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position.

The Home Depot
(501)941-4350
555 Going Road
Cabot, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Whit Davis Lumber Plus
(501) 843-7009
340 Arena Road
Cabot, AR
 
LOWE'S OF JACKSONVILLE, AR
501 241-1500
2301 T.P. WHITE DRIVE JACKSONVILLE, AR, 72076
Jacksonville, AR
 
Lowe's
(501) 241-1500
2301 T. P. White Drive
Jacksonville, AR
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Lowe's
(501) 955-2219
4330 East Mccain Boulevard
North Little Rock, AR
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(501)945-3500
4325 E McCain Blvd
North Little Rock, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 3933 / Cross Merch
(501) 843-2206
W Main Street
Cabot, AR
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Whit Davis Lumber Plus
(501) 982-2156
723 School Dr
Jacksonville, AR
 
Fastenal- Jacksonville
501-982-2442
617 J.P. Wright Loop Jacksonville, AR, 72076
Jacksonville, AR
 
LOWE'S OF N. LITTLE ROCK, AR
501 955-2219
4330 EAST MCCAIN BOULEVARD NORTH LITTLE ROCK, AR, 72117
North Little Rock, AR
 

Fast Accurate Height Adjustments

Fast Accurate Height Adjustments

 

    

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position. The height gauge measures up to 3-1/4-in. in 1/32-in. graduations. The zero line ("0") on the slide block acts as a pointer. The micro-adjust knob is calibrated so that one-quarter turn equals 1/128-in. For ultra smooth operation, the slide block is dovetailed into hand-lapped ways in the body. The gauge's steel foot is 1/2-in.-wide, so you don't have to locate top dead center on your saw blade to obtain accurate measurements. Simply position the Angle Wright approximately where the tablesaw's blade reaches it's highest point. Gently rocking the blade as you lower the foot.
Decimal and metric scales are also available in 0.025-in.  and  1-mm. graduations. They both use vernier scales on the slide bar that permit readings to 0.001 inches.

Source
21st Century Scientific, (800) 448-3680, www.anglewright.com, Angle Wright, $135

Click here to read the rest of the article from American Woodworker