American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Fast Accurate Height Adjustments East Greenwich RI

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position.

Woodcraft - Providence, RI
(401) 886-1175
1000 Division Street
East Greenwich, RI

Data Provided by:
The Home Depot
(401)823-5173
700 Centre Of N E Blvd
Coventry, RI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(401)845-5092
878 W Main Road
Middletown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(401) 267-6330
1530 Davisville Road
North Kingstown, RI
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

S&t True Value Hardware
(401) 397-6300
2300 Nooseneck Hill Rd
Coventry, RI
 
The Home Depot
(401)295-1184
1255 Ten Rod Road
North Kingstown, RI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Liberty Cedar, Inc.
(401) 789-6626
325 Liberty Lane
West Kingston, RI

Data Provided by:
St. Angelo Hardwoods, Inc. - Genuine Asian Teak Specialist
(401) 624-3900
490 Eagleville Road
Tiverton, RI

Data Provided by:
Wickford Lumber Co True Value
(401) 295-8866
434 Tower Hill Road
North Kingstown, RI
 
Rhode Island Mall
(401) 827-4800
650 Bald Hill Rd
Warwick, RI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5
Store Features
Mon:9-21
Tue:9-21
Wed:9-21
Thu:9-21
Fri:9-21
Sat:8-21
Sun:9-18.5

Data Provided by:

Fast Accurate Height Adjustments

Fast Accurate Height Adjustments

 

    

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position. The height gauge measures up to 3-1/4-in. in 1/32-in. graduations. The zero line ("0") on the slide block acts as a pointer. The micro-adjust knob is calibrated so that one-quarter turn equals 1/128-in. For ultra smooth operation, the slide block is dovetailed into hand-lapped ways in the body. The gauge's steel foot is 1/2-in.-wide, so you don't have to locate top dead center on your saw blade to obtain accurate measurements. Simply position the Angle Wright approximately where the tablesaw's blade reaches it's highest point. Gently rocking the blade as you lower the foot.
Decimal and metric scales are also available in 0.025-in.  and  1-mm. graduations. They both use vernier scales on the slide bar that permit readings to 0.001 inches.

Source
21st Century Scientific, (800) 448-3680, www.anglewright.com, Angle Wright, $135

Click here to read the rest of the article from American Woodworker