American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Fast Accurate Height Adjustments Oconomowoc WI

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position.

The Home Depot
(262)646-9160
3400 Hillside Dr
Delafield, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(262)717-0344
2320 W Bluemound Rd
Waukesha, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(262)363-7141
232 E Wolf Run
Mukwonago, WI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Kmart 3692 / Cross Merch
(262) 567-2300
1450 Summit Avenue
Oconomowoc, WI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Ace Hardware of Oconomowoc
(262) 567-8288
1081 Summit Ave
Oconomowoc, WI
 
Boehm-Madisen Lumber Co.
(262) 544-4660
N16 W22100 Jericho Dr.
Waukesha, WI

Data Provided by:
Kettle Moraine Hardwoods
(262) 644-8119
5261 Aurora Rd.
Hartford, WI

Data Provided by:
The Home Depot
(262)502-9840
N94 W 18375 Thunder Rdg
Menomonee Falls, WI
Hours
Mon-Sat: 8:00am-8:00pm
Sun: 9:00am-6:00pm

Lorleberg True Value
(262) 567-0267
900 E Wisconsin Ave
Oconomowoc, WI
 
Warden's Ace Hardware
(262) 646-4101
2835 Heritage Dr, walmart plaza shopping center
Delafield, WI
 
Data Provided by:

Fast Accurate Height Adjustments

Fast Accurate Height Adjustments

 

    

The Angle Wright is a precision instrument that helps you make quick and accurate height adjustments of router bits, jointer knives and table saw blades. Made in the USA of anodized aluminum and steel, it features recessed brass adjustment knobs that allow the tool to be used flat on its side or in an upright position. The height gauge measures up to 3-1/4-in. in 1/32-in. graduations. The zero line ("0") on the slide block acts as a pointer. The micro-adjust knob is calibrated so that one-quarter turn equals 1/128-in. For ultra smooth operation, the slide block is dovetailed into hand-lapped ways in the body. The gauge's steel foot is 1/2-in.-wide, so you don't have to locate top dead center on your saw blade to obtain accurate measurements. Simply position the Angle Wright approximately where the tablesaw's blade reaches it's highest point. Gently rocking the blade as you lower the foot.
Decimal and metric scales are also available in 0.025-in.  and  1-mm. graduations. They both use vernier scales on the slide bar that permit readings to 0.001 inches.

Source
21st Century Scientific, (800) 448-3680, www.anglewright.com, Angle Wright, $135

Click here to read the rest of the article from American Woodworker