American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Folding Outfeed Table Greeneville TN

For those of you with a contractor’s saw on a mobile base, we’ve designed the kind of table you’d wish the saw had to begin with. It goes wherever the saw goes. Folded up, it doubles as a sturdy assembly table. Folded down, you still get an additional foot of support for cutting short stuff.

Full Cycle Woodworks Inc.
(423) 272-9004
1600 Hwy 70 North
Rogersville, TN

Data Provided by:
Ace Hardware
(423) 639-6223
1023 W Main St
Greeneville, TN
 
Lowe's
(423) 639-0012
2375 East Andrew Johnson Highway
Greeneville, TN
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Lowe's
(423) 788-7000
1498 E. Jackson Boulevard
Jonesborough, TN
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Appalachian Stoneworks
(866) 389-4260
412 Kinchloe Mill Rd
Jonesborough, TN

Data Provided by:
Fastenal- Greeneville
423-638-3622
730 W. Andrew Johnson Hwy Greeneville, TN, 37743
Greeneville, TN
 
Kmart 3773 / Cross Merch
(423) 636-1118
1355 Tusculum Blvd
Greeneville, TN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

LOWE'S OF GREENEVILLE, TENN.
423 639-0012
2375 EAST ANDREW JOHNSON HIGHWAY GREENEVILLE, TN, 37745
Greeneville, TN
 
Olde Towne Ace Hardware
(423) 913-1606
220 N 2nd Ave
Jonesborough, TN
 
The Home Depot
(615)220-5044
551 President Place
Smyrna, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Folding Outfeed Table

Folding Outfeed Table

Open, it supports 8-ft. long stock. Closed, it's as compact as your saw.

by George Vondriska

Roller stands are okay, but every saw really ought to have an outfeed table. It makes ripping lumber or plywood a lot more convenient and much safer. The bigger the table, the better. But how’s it going to fit into a small shop?

For those of you with a contractor’s saw on a mobile base, we’ve designed the kind of table you’d wish the saw had to begin with. It goes wherever the saw goes. Folded up, it doubles as a sturdy assembly table. Folded down, you still get an additional foot of support for cutting short stuff. We’ve also built in storage space for all the gear a saw needs: a rip fence, miter gauge, push sticks and extra blades. The only thing we haven’t figured out is how to store the legs; if you have a solution, send it in!

Tools and Materials

You’ll need a tablesaw, router and jigsaw, and that’s about it. We used 3/4-in. oak plywood for most of the understructure because it’s strong. The tops are made from melamine; it’s slippery and easy to clean. The edges and legs are oak because they’ll take a lot of dings, but any hardwood will do. The total cost of material and hardware is about $200.

We’ve looked at a lot of contractor’s saws to make sure these plans would work, but there’s a chance your saw may be an odd size. The table will still work, but you may have to modify some of its dimensions before you make the first cut (see “Measure Your Saw”, below).

Build the Platform

1. Cut parts A through F to size. Glue banding (M) on top of the riser (F). Cut slots in the outer ribs (D) by connecting two 1/2-in. holes with jigsaw cuts (Photo 1). Cut recesses for motor clearance in the deck (A) and rear support arm (B, Fig. A, Detail 1, below).

2. Screw the support arms to the deck. Add the outer ribs using one of the inner ribs (C) as a spacer (Photo 2). Add the back (E).

3. Take the motor off the saw. Get some help to remove the upper half of the tablesaw from the stand. Place the platform on the stand with the front support arm pushed tight against the stand. The distance from the left edge of the stand to the outside of the left outer rib is determined by your saw’s Offset measurement (see “Measure Your Saw”,  below). Mark the locations of the saw-to-stand bolt holes (Photo 3). 

4. Drill the bolt holes through the deck, replace the saw and bolt the saw to the base. Replace the original bolts with longer ones if necessary.

5. Cut slots in the riser (F). If you have moved the inner ribs from the locations in our plan, check the slot locations so they don’t run into the ribs.

6. Clamp the riser to the back of the platform (Photo 4). Use a straightedge to level the riser with the saw table.

Click here to read the rest of the article from American Woodworker