American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Folding Outfeed Table West Fargo ND

For those of you with a contractor’s saw on a mobile base, we’ve designed the kind of table you’d wish the saw had to begin with. It goes wherever the saw goes. Folded up, it doubles as a sturdy assembly table. Folded down, you still get an additional foot of support for cutting short stuff.

The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Fastenal- Fargo
701-277-0823
3215 Main Ave Suite A Fargo, ND, 58102
Fargo, ND
 
Lamperts
(701) 492-0292
4115 32nd Ave Sw
Fargo, ND
 
West Acres Regional S/C
(701) 281-5800
3902 13Th Ave South Ste 600
Fargo, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Fastenal- Fargo
701-271-1055
3239 15th St S Suite A Fargo, ND, 58106
Fargo, ND
 
Ostrom's Hardware
(701) 282-3046
1100 13th Ave E Ste 2, 9th St and 13th Ave E
West Fargo, ND
 
LOWE'S OF FARGO, ND
701 433-2160
5001 13TH AVENUE SW FARGO, ND, 58103
Fargo, ND
 
Scheels Ace Hardware
(701) 232-8903
3202-13th Ave S
Fargo, ND
 
Dakota Fastening
(701) 298-3691
3401 1/2 Interstate Blvd Fargo, ND, 58103
Fargo, ND
 
Kmart 4057 / Cross Merch
(701) 232-8943
2301 S University Dr
Fargo, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Folding Outfeed Table

Folding Outfeed Table

Open, it supports 8-ft. long stock. Closed, it's as compact as your saw.

by George Vondriska

Roller stands are okay, but every saw really ought to have an outfeed table. It makes ripping lumber or plywood a lot more convenient and much safer. The bigger the table, the better. But how’s it going to fit into a small shop?

For those of you with a contractor’s saw on a mobile base, we’ve designed the kind of table you’d wish the saw had to begin with. It goes wherever the saw goes. Folded up, it doubles as a sturdy assembly table. Folded down, you still get an additional foot of support for cutting short stuff. We’ve also built in storage space for all the gear a saw needs: a rip fence, miter gauge, push sticks and extra blades. The only thing we haven’t figured out is how to store the legs; if you have a solution, send it in!

Tools and Materials

You’ll need a tablesaw, router and jigsaw, and that’s about it. We used 3/4-in. oak plywood for most of the understructure because it’s strong. The tops are made from melamine; it’s slippery and easy to clean. The edges and legs are oak because they’ll take a lot of dings, but any hardwood will do. The total cost of material and hardware is about $200.

We’ve looked at a lot of contractor’s saws to make sure these plans would work, but there’s a chance your saw may be an odd size. The table will still work, but you may have to modify some of its dimensions before you make the first cut (see “Measure Your Saw”, below).

Build the Platform

1. Cut parts A through F to size. Glue banding (M) on top of the riser (F). Cut slots in the outer ribs (D) by connecting two 1/2-in. holes with jigsaw cuts (Photo 1). Cut recesses for motor clearance in the deck (A) and rear support arm (B, Fig. A, Detail 1, below).

2. Screw the support arms to the deck. Add the outer ribs using one of the inner ribs (C) as a spacer (Photo 2). Add the back (E).

3. Take the motor off the saw. Get some help to remove the upper half of the tablesaw from the stand. Place the platform on the stand with the front support arm pushed tight against the stand. The distance from the left edge of the stand to the outside of the left outer rib is determined by your saw’s Offset measurement (see “Measure Your Saw”,  below). Mark the locations of the saw-to-stand bolt holes (Photo 3). 

4. Drill the bolt holes through the deck, replace the saw and bolt the saw to the base. Replace the original bolts with longer ones if necessary.

5. Cut slots in the riser (F). If you have moved the inner ribs from the locations in our plan, check the slot locations so they don’t run into the ribs.

6. Clamp the riser to the back of the platform (Photo 4). Use a straightedge to level the riser with the saw table.

Click here to read the rest of the article from American Woodworker