American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Forstner Bits North Brunswick NJ

The knife-edge is the most traditional Forstner design and does a great job of cutting nonstandard holes. That's because it has the fewest rim interruptions. Its rim is ground to create an inside bevel with a sharp knife-edge.

The Home Depot
(732)438-5980
4095 US Route 1
Monmouth Junction, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)987-8686
701 Nassau Park Blvd
Princeton, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)426-2441
739 Route 33 West
E Windsor, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)585-0411
750 Highway Rt 130
Robbinsville, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Willard Brothers Lumber
(800) 320-6519
300 Basin Road
Trenton, NJ

Data Provided by:
AGINCOURT
(908) 874-8234
212 E Mountain Rd
Hillsborough, NJ

Data Provided by:
The Home Depot
(908)252-0101
736 Route 202 South
Bridgewater, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(908)222-7700
1515 Route 22
Watchung, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)393-3697
1621 N Olden Avenue
Ewing, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(908)782-2577
244 Highway 202
Flemington, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Forstner Bits

Forstner Bits

A Forstner Bit can drill holes other bits only dream about. 

by Bruce Kieffer

Forstner-style bits can go where no other drill bits dare. The reason is simple: A Forstner bit is rim-guided while other bits are center-point guided. That means you can use all or only part of the bit’s diameter to drill overlapped, angled or partial holes. Forstner bits also shine when it comes to drilling clean, precise 90-degree holes and large-diameter holes. Carbide-tipped Forstner-style bits excel at drilling the precise, flat-bottomed holes required for European-style hinges. Plus, unlike other drill bits, the rim-guided Forstner bit can drill into end grain without deflection.

Forstner bits do have their drawbacks and are not a substitute for your everyday twist- or brad-point bits. For one thing, they are more expensive: A 1/4-in. Forstner bit costs between $3 and $23. They’re also designed pri-marily for use in a drill press, although Forstner bits that are 1 in. or smaller can be used in a hand drill if the bit’s center point is firmly engaged. Forstners also require a very slow rpm rate and thus are slow cutting. Finally, they are very difficult to sharpen. 

Bit Types

Description

The knife-edge is the most traditional Forstner design and does a great job of cutting nonstandard holes. That’s because it has the fewest rim interruptions. Its rim is ground to create an inside bevel with a sharp knife-edge. The rim scores the wood before the chip lifters remove the wood from the hole, creating a very smooth, flat-bottomed hole with no tear-out.

  The knife-edge rim’s “rubbing” cut generates a lot of heat from friction. Because of this, the style is found primarily in 1-in.-dia. or smaller bits, whose rim speed is relatively slow. To avoid overheating, follow the speed recommendations that come with each bit. 

Knife Edge

A new Forstner rim design is the wavy edge. Manufacturers claim their wavy-edge bits run cooler than knife-edge Forstners. The idea is that the complex grind of the wavy edge creates ultrasharp points along the rim that help break up the wood chips for easier passage through the bit’s throat openings. 

  The wavy-edge rim performs just as well as the knife-edge does on 90-degree holes. However, holes drilled by a wavy-edge bit on a board’s edge without the center point engaged have slightly rougher sidewalls than those made by the knife-edge bits. And starting a hole at an angle produces a bit of chatter until the center point engages.

Wavy Edge

These bits, with sawlike teeth ground into the rim, are great for drilling 90-degree holes. The rim teeth cut, rather than score, the wood, generating less heat and allowing a faster feed rate than knife-edge bits do.

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details