American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Cabinetry Mount Morris MI

Here you will learn a technique on how to create frameless cabinet joinery. Cabinetry will open up a new avenue for creativity and you will find yourself building many useful woodworking projects. Make sure you have the right power tools when cabinet making. You will find everything you need at the hardware supply stores in Mount Morris, MI listed below.

The Home Depot
(810)715-1700
4245 E Court St
Burton, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(810)230-8784
4380 W Corunna Rd
Flint, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(810)245-3485
1500 Summit Drive
Lapeer, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Martin's Hardware Genesee Inc
(810) 640-1300
7256 N. Genesee
Genesee, MI
 
West Gamble Store
(810) 686-0920
146 W. Vienna St.
Clio, MI
 
The Home Depot
(810)230-6430
5300 Pierson Road
Flushing, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(810)232-7113
1222 West Hill Rd
Flint, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockwell Ace Hardware
(810) 686-4110
G 7070 N Saginaw Street
Mount Morris, MI
 
Beauchamp's Ace Hardware
(810) 789-7871
1101 W Pierson Rd
Flint, MI
 
Clio - D
(810) 564-3088
4290 Vienna Rd
Clio, MI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Cabinetry

Frameless Cabinet Joinery

By Dave Munkittrick

I’ve always liked the clean, modern look of cabinets built without face frames. My early attempts involved building plywood boxes first and applying hardwood edging later. But cutting, fitting, gluing and clamping each edging piece was frustratingly slow --- and that was nothing compared to leveling the edging flush with the plywood. A task that was especially aggravating on the inside corners. 

I had almost given up making this style of cabinet when I learned a new technique that streamlines construction. It allows you to put the edging on before assembly. Flushing up the edging on a flat panel is no problem. I can even pre-finish the cabinet parts before gluing them together. I get perfect looking butt joints and an almost invisible line where the edging joins the plywood (see photo below). 

Here’s how it works:

1. Cut all your cabinet parts to size. Leave one shelf about 1/2-in. long to use later for test cuts. 

2. Cut all the rabbets and dadoes (Photo 1). Because this technique requires consistent dado depth I prefer to use a router and a jig rather than a tablesaw. For more on the jig we used.

3. Glue the hardwood edges to the side panels and shelves by sandwiching a single piece of hardwood between two panels (Photo 2). The hardwood piece is twice as thick as the finish thickness of the edging plus an extra 1/8-in. for the saw kerf. For example, for a 3/16-in. thick hardwood edge use a 1/2-in. thick piece of hardwood. I like the looks of a thin edge and it still offers plenty of protection for the plywood edge. 

4. Rip the glued-together panels (Photo 3). The hardwood edge  creates stopped dados and rabbets on the cabinet sides. 

5. Flush up the edging with the panels. I start with a block plane (Photo 4) and finish with a light sanding. Using a power sander is asking for a sand-through on the veneer. 

6. Trim the edging to length with a handsaw.

7. Use the extra long shelf to set your jointer for notching the plywood (Photo 5). It’ll take some trial and error to get the depth of cut just right. The extra length on the shelf allows you to trim and retest the joints’ fit.

8. Test the shelf’s fit by sliding it forward in the rabbet (Photo 6). If the notched edge butts into the back of the side’s edging, the cut needs to be made deeper. If the notch slides over the side’s edging and leaves a gap, the jointer needs to be set for a shallower cut. 

9. Once you get the right fit, go ahead and notch all the shelves. 

10. Dry fit the cabinet to check for any problem areas. An open joint is almost always the result of a high spot in a dado. 

11. Do any finish sanding on the edges while the cabinet is clamped together. It’s too easy to ruin the fit if you sand the edging when the cabinet is apart.

12. Disassemble the  cabinet and finish sand the flat panels taking care not to round ...

Click here to read the rest of the article from American Woodworker