American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

French Polishing Claremore OK

What is French polish? It’s simply shellac and a little oil applied with a pad. The oil acts as a lubricant when you apply the finish. French polish is available as commercially made products, also labeled as padding lacquer or friction polish.

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Claremore - Auth Hometown
(918) 343-2500
1648 North Lynn Riggs Blvd
Claremore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20

Fastenal- Claremore
918-342-4548
1614 North Lynn Riggs Blvd Claremore, OK, 74017
Claremore, OK
 
Cribbets True Value
(918) 371-3306
1008 Main St
Collinsville, OK
 
LOWE'S OF OWASSO, OK
918 274-0881
12001 E. 96TH STREET NORTH OWASSO, OK, 74055
Owasso, OK
 
Pixley Lumber Co
(918) 341-4223
715 W Will Rogers
Claremore, OK
 
Lowe's
(918) 923-1030
1746 South Lynn Riggs Boulevard
Claremore, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Westlake Ace Hardware
(918) 343-3117
810 N Lynn Riggs Blvd
Claremore, OK
 
Lowe's
(918) 274-0881
12001 E. 96Th Street North
Owasso, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Pryor Lumber
(918) 825-2260
1031 West Highway 20
Pryor, OK
 

French Polishing

French Polishing

Six Easy Steps to a Beautiful Finish

by Alan Lacer

French polish adds extraordinary depth to gorgeous wood. This finish is perfect for bowls, vessels, lamps and other turnings that aren’t handled often or are exposed to moisture, alcohol or heat. It’s easy to apply: Just hold a cloth moistened with the finish directly to your project as it spins on the lathe. 

What is French polish? It’s simply shellac and a little oil applied with a pad. The oil acts as a lubricant when you apply the finish. French polish is available as commercially made products, also labeled as padding lacquer or friction polish, but I prefer to make my own from flakes, which guarantees freshness. You can achieve a variety of effects because shellac is available in a range of colors (see “Buying Shellac,” below). Here’s how you can mix your own French polish, choose different colors, apply it and rub it out. 

Sand with Fine Grits

Thoroughly sand all surfaces of your project to eliminate torn grain, spirals and ridges. Start with 120-grit and progress through 150-, 180- and 220-grit sandpaper (Photo 1). If sanding scratches still show, continue with 320- or 400-grit sandpaper. Maple and cherry often require these finer grits. After sanding, remove the dust using an alcohol-moistened paper towel.

Photo 1: Sand your piece to eliminate flaws and sanding rings. Remove sanding dust using a paper towel moistened with denatured alcohol held against the workpiece while it’s spinning.

Mix the French Polish

You can use shellac flakes or premixed liquid shellac to make French polish. Either way, your goal is to make a 1-1/2-lb. cut, which is the equivalent of mixing 1-1/2 lbs. of flakes with 1 gal. of denatured alcohol. That’s far too much finish for most projects, however. If you use flakes, dissolve 1-1/2 oz. of flakes with 1 cup of denatured alcohol. Premixed liquid shellac comes in a 3-lb. cut. To make approximately a 1-1/2 lb. cut, thin it with an equal amount of denatured alcohol.

The final ingredient of French polish is an oil, which acts a lubricant to prevent your applicator cloth from dragging or sticking. Add 1 tablespoon of mineral oil for every 3 liquid oz. of 1-1/2-lb.-cut shellac (Photo 2).

Photo 2: French polish is a mixture of shellac and oil. Little oil is needed; it acts as a lubricant for the shellac.

Apply the Finish

Adjust your lathe to run at a moderate speed, about 500 to 800 rpm, slower for large-diameter turnings. Make an applicator for applying the French polish from a densely woven, soft, white cotton cloth that has been washed many times to remove all lint. Soften the pad with alcohol before dipping it into the French polish.

Shake the French polish to suspend the oil, as though it were an oil-and-vinegar salad dressing. Turn on the lathe, saturate the cloth pad and flow on the finish (Photo 3). If the cloth grabs, add a half teaspoon of oil. Let thi...

Click here to read the rest of the article from American Woodworker