American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

French Polishing Lake Villa IL

What is French polish? It’s simply shellac and a little oil applied with a pad. The oil acts as a lubricant when you apply the finish. French polish is available as commercially made products, also labeled as padding lacquer or friction polish.

The Home Depot
(847)223-0336
2050 N Illinois Rt 83
Round Lake Beach, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)599-0180
6625 Grand Ave
Gurnee, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)625-1020
2001 Belvedere Rd
Waukegan, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(815)385-9503
2461 N Richmond Rd
McHenry, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)726-0707
670 S Rand Road
Lake Zurich, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)973-8196
2731 Hartigan Rd
Volo, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(847)566-6532
3200 West Route 60
Mundelein, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Russell Mill
(847) 395-5190
15780 W Russell Rd
Zion, IL

Data Provided by:
The Home Depot
(847)549-0110
493 N Milwaukee Ave
Vernon Hills, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(815)479-1030
4447 US Route 14
Crystal Lake, IL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

French Polishing

French Polishing

Six Easy Steps to a Beautiful Finish

by Alan Lacer

French polish adds extraordinary depth to gorgeous wood. This finish is perfect for bowls, vessels, lamps and other turnings that aren’t handled often or are exposed to moisture, alcohol or heat. It’s easy to apply: Just hold a cloth moistened with the finish directly to your project as it spins on the lathe. 

What is French polish? It’s simply shellac and a little oil applied with a pad. The oil acts as a lubricant when you apply the finish. French polish is available as commercially made products, also labeled as padding lacquer or friction polish, but I prefer to make my own from flakes, which guarantees freshness. You can achieve a variety of effects because shellac is available in a range of colors (see “Buying Shellac,” below). Here’s how you can mix your own French polish, choose different colors, apply it and rub it out. 

Sand with Fine Grits

Thoroughly sand all surfaces of your project to eliminate torn grain, spirals and ridges. Start with 120-grit and progress through 150-, 180- and 220-grit sandpaper (Photo 1). If sanding scratches still show, continue with 320- or 400-grit sandpaper. Maple and cherry often require these finer grits. After sanding, remove the dust using an alcohol-moistened paper towel.

Photo 1: Sand your piece to eliminate flaws and sanding rings. Remove sanding dust using a paper towel moistened with denatured alcohol held against the workpiece while it’s spinning.

Mix the French Polish

You can use shellac flakes or premixed liquid shellac to make French polish. Either way, your goal is to make a 1-1/2-lb. cut, which is the equivalent of mixing 1-1/2 lbs. of flakes with 1 gal. of denatured alcohol. That’s far too much finish for most projects, however. If you use flakes, dissolve 1-1/2 oz. of flakes with 1 cup of denatured alcohol. Premixed liquid shellac comes in a 3-lb. cut. To make approximately a 1-1/2 lb. cut, thin it with an equal amount of denatured alcohol.

The final ingredient of French polish is an oil, which acts a lubricant to prevent your applicator cloth from dragging or sticking. Add 1 tablespoon of mineral oil for every 3 liquid oz. of 1-1/2-lb.-cut shellac (Photo 2).

Photo 2: French polish is a mixture of shellac and oil. Little oil is needed; it acts as a lubricant for the shellac.

Apply the Finish

Adjust your lathe to run at a moderate speed, about 500 to 800 rpm, slower for large-diameter turnings. Make an applicator for applying the French polish from a densely woven, soft, white cotton cloth that has been washed many times to remove all lint. Soften the pad with alcohol before dipping it into the French polish.

Shake the French polish to suspend the oil, as though it were an oil-and-vinegar salad dressing. Turn on the lathe, saturate the cloth pad and flow on the finish (Photo 3). If the cloth grabs, add a half teaspoon of oil. Let thi...

Click here to read the rest of the article from American Woodworker