American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Garden Chairs New Albany IN

Stylish and comfortable, these chairs are also built to last. Made of rot-resistant white oak, with robust joinery secured with weatherproof glue, they’re guaranteed to become some of your garden’s most cherished perennials.

Bill Kraemer Veneers, Inc.
(812) 944-6491
2235 Croydon Pike
New Albany, IN

Data Provided by:
The Home Depot
(812)282-0470
1000 East Hwy 131
Clarksville, IN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

FormWood Industries
(812) 284-3676
1601 Production Road
Jeffersonville, IN

Data Provided by:
The Home Depot
(502)933-3332
6840 Dixie Hwy
Louisville, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(502)491-3682
2600 S Hurstbourne Pkwy
Louisville, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(812)941-9641
2239 State Street
New Albany, IN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Marwood, Inc (See our website for monthly veneer special offers)
(812) 288-8344
2901 Hamburg Pike
Jeffersonville, IN

Data Provided by:
The Home Depot
(502)899-3706
964 Breckenridge Lane
Louisville, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Louisville, KY
(502) 671-0900
1850 So. Hurstbourne Pkwy
Louisville, KY

Data Provided by:
The Home Depot
(502)964-1845
8232 Preston Hwy
Louisville, KY
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Garden Chairs

Garden Chairs

Enjoy your setting while comfortably sitting.

by Tim Johnson

Stylish and comfortable, these chairs are also built to last. Made of rot-resistant white oak, with robust joinery secured with weatherproof glue, they’re guaranteed to become some of your garden’s most cherished perennials. 

We’ve engineered the building process so you’ll be able to fit every joint using shop-made jigs and simple procedures. There are zillions of mortises, but they’re all routed from only two basic setups that you’ll quickly master. Making these chairs in multiples is really only a matter of physical endurance. White oak is hard and heavy!

Every structural joint consists of two plunge-routed mortises joined by a loose tenon. This variation is just as strong as traditional mortise and tenon construction and it’s much easier to accomplish, particularly on this chair’s angled arm and stretcher joints.

Lumber and Tools

White oak is a bargain compared to other rot-resistant hardwoods like teak and mahogany, and it’s readily available in a variety of thicknesses. We used 8/4 stock for the legs (wide boards so we didn’t have to glue up the blanks), 6/4 for the arms, rails and stretchers and 4/4 for the slats and tenon stock. For dimensional stability, we chose boards with straight grain. Each chair requires about 35 bd. ft. of lumber. We paid $160 per chair for our rough-sawn stock. 

Routing all the mortises will give your plunge router a real workout. It must have a 1/2-in. collet, an edge guide, 2-1/8 in. of plunge capacity and the guts to plunge deep in white oak (at least 1-1/2 hp). 

This project also requires a tablesaw and bandsaw, a drill press with a sanding drum and a router table. You’ll need 3/8-in. and 1/2-in. straight bits for mortising, a 2-in. flush-trim bit, a 1/4-in. round-over bit and a chamfering bit (see Sources, page 87). A jointer and planer are recommended, but not essential. You can have your stock milled to thickness at the lumberyard. 

Building Tips

Squarely-cut blanks are essential for sound joinery and good results. Make sure your tablesaw’s miter gauge makes square crosscuts. The heavy leg blanks may require a crosscut sled or an accurate chop saw.

Use templates to duplicate the shaped legs, arms and seat rails (Fig. D - G, page 84). 1/2-in.-thick MDF is excellent template material (available at most home centers for $5 per 2-ft. x 4-ft. sheet).

Use layout marks to guarantee that mortises and adjoining pieces go where they’re supposed to go.

Plunge-rout the mortises, using a straight bit, an edge guide and clamped-on stop blocks. Mortises are either routed into the end grain using a jig, or into the long grain, using a flush-mounted support block. 

Rout mortises before you cut profiles. It’s much easier to fit the angled joints around the mortises than vice-versa.

Always rout from...

Click here to read the rest of the article from American Woodworker