American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Bellingham WA

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

The Home Depot
(360)715-0090
420 Telegraph Rd
Bellingham, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Bellis Fair Mall
(360) 650-1200
20 Bellis Fair Pkwy
Bellingham, WA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Bellingham - D
(360) 734-9550
1001 E Sunset Dr
Bellingham, WA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Hardware Sales, Inc.
(360) 734-6140
2034 James Street
Bellingham, WA
 
Ferndale Ace Hardware
(360) 656-6882
5715 Fourth Ave, Next to the Ferndale post office
Ferndale, WA
 
The Home Depot
(360)757-1986
2001 Market Place Drive
Burlington, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Lowe's
(360) 734-2659
1050 East Sunset Drive
Bellingham, WA
Hours
M-SA 6 am - 10 pm
SU 7 am - 9 pm

LOWE'S OF BELLINGHAM, WA
360 734-2659
1050 EAST SUNSET DRIVE BELLINGHAM, WA, 98226
Bellingham, WA
 
HARDWARE SALES INC
(360) 734-6140
2034 JAMES STREET BELLINGHAM, WA, 98225
Bellingham, WA
 
OSO Lumber/Ferndale
(360) 435-8397
5880 Portal Way Ferndale, WA, 98248
Ferndale, WA
 

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker