American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Essex Junction VT

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

The Home Depot
(802)872-0039
759 Harvest Lane
Williston, VT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Essex Equipment
(802) 879-0767
26 Kellogg Road
Essex Junction, VT
 
Lowe's
(802) 662-9131
10 Susie Wilson Road
Essex Junction, VT
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Harvey Industries/White River Jct
(802) 295-3700
1354 North Heartland Rd White River Jct, VT, 05495
White River Jct, VT
 
Jerihill Home Center
(802) 899-1277
249 Vt Route 15
Jericho, VT
 
Bibens Ace-Essex
(802) 879-0249
15 Essex Way, Essex Shoppes & Cinema
Essex Junction, VT
 
Lowe's of Essex
802-662-9131
10 Sussie Wilson Rd Essex Junction, VT, 05452
Essex Junction, VT
 
Harvey Industries/Williston
(802) 660-8111
71 Leroy Road Williston, VT, 05495
Williston, VT
 
Russell Supply
(802) 863-1177
9 Gregory Drive South Burlington, VT, 05407
South Burlington, VT
 
Lowe's
(802) 318-9052
189 Hannaford Drive
South Burlington, VT
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker