American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Mililani HI

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

The Home Depot
(808)455-1200
1021 Kamehameha Highway
Pearl City, HI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-9:00pm

The Home Depot
(808)521-7355
421 Alakawa St
Honolulu, HI
Hours
Mon-Sun: 5:00am-10:00pm

Kmart 7478 / Cross Merch
(808) 676-8886
94 - 825 Lumiaina St
Waipahu, HI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

LOWE'S OF WAIPAHU, HI
808 676-8381
94-805 LUMIAINA STREET WAIPAHU, HI, 96797
Waipahu, HI
 
Fastenal- Pearl City
808-456-0871
96-1333 Waihona St Unit B Pearl City, HI, 96782
Pearl City, HI
 
The Home Depot
(808)674-6120
4600 Kapolei Parkway
Kapolei, HI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-9:00pm

Woodcraft - Honolulu, HI
(808) 841-9876
1311 Kalani St.
Honolulu, HI

Data Provided by:
Lowe's
(808) 676-8381
94-805 Lumiaina Street
Waipahu, HI
Hours
M-SA 6 am - 10 pm
SU 7 am - 9 pm

Pioneer Ace Hardware
(808) 622-1641
930 Kilani Ave
Wahiawa, HI
 
98-180 Kamehameha Highway
(808) 487-4211
Pearlridge S/C Ste 60-S-1
Aiea, HI
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-18
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-18

Data Provided by:

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker