American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Saint Cloud MN

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

The Home Depot
(320)252-3262
401 2nd Street South
Waite Park, MN
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Crossroads Ctr
(320) 202-6000
4101 W Division St
Saint Cloud, MN
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Kmart 4882 / Cross Merch
(320) 251-3343
40 2Nd St S
Waite Park, MN
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Denny & Kathy's Ace Hardware
(320) 253-0370
2006 8th St N
Saint Cloud, MN
 
Simonson Lumber
(320) 252-9385
2455 12th St S.e.
St Cloud, MN
 
Fastenal- St. Cloud
320-252-3655
2803 Clearwater Rd St. Cloud, MN, 56301
St. Cloud, MN
 
Denny & Kathy's Ace Hardware
(320) 258-4044
3123 Roosevelt Rd, Located near St. Cloud Medical Group South Campus
Saint Cloud, MN
 
Thomas Tool- St. Cloud
(320) 253-4526
1201 Lincoln Avenue NE St Cloud, MN, 56302
St Cloud, MN
 
Fastenal- Sauk Rapids
320-253-4544
1000 Benton Drive S Suite 411 Sauk Rapids, MN, 56379
Sauk Rapids, MN
 
Lee's Ace Hardware
(320) 363-4281
213 Cedar St
Saint Joseph, MN
 

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker