American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Salina KS

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

LOWE'S OF SALINA, KS
785 452-9303
3035 SOUTH 9TH STREET SALINA, KS, 67401
Salina, KS
 
Waters True Value
(785) 823-6400
460 S Ohio St
Salina, KS
 
Lowe's
(785) 452-9303
3035 South 9Th Street
Salina, KS
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Ace Home Center
(785) 827-4474
321 S Broadway Blvd
Salina, KS
 
Lindsborg Hardware
(785) 227-2696
115 North Main
Lindsborg, KS
 
Fastenal- Salina
785-825-1900
330 E. Schilling Rd Salina, KS, 67401
Salina, KS
 
MIDWAY WHOLESALE - SALINA
(785) 823-7874
1027 York Avenue Salina, KS, 67402
Salina, KS
 
Kmart 7169 / Cross Merch
(785) 825-1591
400 S Broadway
Salina, KS
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

175 Central Mall
(785) 826-4300
2259 S 9Th St
Salina, KS
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-21
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-21

John' Door Service
(785) 826-9965
500 N. 5th. st.
SALINA , KS
Services Offered
GARAGE DOOR RESIDENTAL,COOMERCIAL SERVICE
Hours
7 AM - 6PM AFTER HOURS EMERGENCY SERVICE

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker