American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Goof-Proof Crown Molding Wasilla AK

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw's left side. For the best results, screw the box to the miter saw's fence. For some cuts, the box's long side goes against the fence.

The Home Depot
(907)357-8181
1255 Palmer Wasilla Hwy
Wasilla, AK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Alaska Industrial Hardware- Wasilla
907-376-5274
751 West Parks Hwy Wasilla, AK, 99654
Wasilla, AK
 
Lowe's
(907) 352-3100
2561 East Sun Mountain Avenue
Wasilla, AK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Spenard Builders Supply- Big Lake
907-892-6001
10927 Big Lake Road Big Lake, AK, 99652
Big Lake, AK
 
Alaska Industrial Hardware- Eagle River
907-694-2988
12330 Old Glenn Hwy Eagle River, AK, 99577
Eagle River, AK
 
Wasilla - B
(907) 352-6800
1000 S Seward Meridian Rd
Wasilla, AK
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Spenard Builders Supply- Wasilla
907-373-2806
2501 E Bogard Road Wasilla, AK, 99654
Wasilla, AK
 
Weld Air Alaska
(907) 373-2000
301 Centaur Wasilla, AK, 99654
Wasilla, AK
 
Spenard Builders Supply- Eagle River
907-694-3527
17320 Northgate Park Eagle River, AK, 99577
Eagle River, AK
 
Home Depot
(907) 644-9012
1715 Abbott RD
Anchorage, AK
 

Goof-Proof Crown Molding

Goof-Proof Crown Molding

By Tom Caspar

Cutting perfect miters on crown molding can be a real challenge. Make a mistake and a lot of expensive wood goes to waste. This method, which uses a shop-made miter box, puts the molding in its “natural” position, the way it will be placed on your project. It’s easy to set up the saw and tweak the miter’s angle for inside and outside joints. The saw’s blade stays at 90 degrees to the table, so you don’t have any complicated compound cuts to set up.

Start by building the miter box (see photo, below). Don’t use screws; you don’t want to accidentally cut into one. Use a combination square to figure out how wide the box’s pieces must be to hold the molding in its natural, upright position. The bottom piece’s width equals the molding’s depth when it’s installed. The side pieces’ width equals the molding’s height when it’s installed plus the thickness of the bottom piece. Cut these pieces about 12 in. long and leave the ends square for now. Glue the box together; then miter the ends. Label each corner.

Cutting miters is very straightforward (see photos, right). For convenience, I always hold the box on the saw’s left side. For the best results, screw the box to the miter saw’s fence. For some cuts, the box’s long side goes against the fence. For others, the short side goes against the fence. Using a high-tooth count blade will produce a very smooth cut, with no tearout on the molding’s face. 

This method won’t work on all saws and all crown moldings. Success depends on the molding’s height and the saw’s capacity. Many tall moldings can be cut this way using a 12-in. saw, but a 10-in. saw may not have adequate clearance.

Build the miter box from three pieces of plywood. Label the corners to indicate how the crown molding is oriented for each miter cut.

Place the molding’s top edge against the label identifying the cut and you can’t go wrong.

This story originally appeared in  American Woodworker Dec/Jan 2007, issue #126.

Source information may have changed since the original publication date.

Dec/Jan 2007, issue #126

Purchase this back issue.

Click here to read the rest of the article from American Woodworker