American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Heavy-Duty Folding Shop Table Lithia Springs GA

You can set it up in only a minute and be ready for routing, sanding, planing—you name it. When you’re done, fold up the table into a super-compact unit only five-inches thick and stow it away. Here today, tucked away tomorrow.

The Home Depot
(770)732-0184
1000 Thornton Road
Lithia Springs, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)691-2077
1032 Research Center
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)577-8311
7399 Douglas Blvd
Douglasville, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)432-9930
2450 Cumberland Pkwy
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)892-8042
650 Ponce DE Leon
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)438-9678
1200 E W Connector SW
Austell, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(678)567-1161
1062 Richard D Sailors
Powder Springs, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)439-0707
145 Depot Drive
Hiram, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)792-6858
2350 Dallas Hwy
Marietta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(404)361-5634
3885 Jonesboro Rd SE
Atlanta, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Heavy-Duty Folding Shop Table

Heavy-Duty Folding Shop Table

by Tom Caspar

Need more bench space? Who doesn’t? Here’s a terrific solution: a folding worktable that’s both big and strong. And we mean strong. 

You can set it up in only a minute and be ready for routing, sanding, planing—you name it. When you’re done, fold up the table into a super-compact unit only five-inches thick and stow it away. Here today, tucked away tomorrow.

Strong = Heavy

This table weighs in at about 70 lbs., a bit more than the full sheet of plywood it’s made from. A lighter table made of smaller plywood parts would be more portable, but not stiff enough to use as a real workbench (Photo 1). For heavy-duty use, extra weight is actually a plus. This table stays put!

Photo 1: This worktable is built for strength. It won’t wobble, sag or walk across the floor. Weighing 70 pounds or so, it’s not going anywhere until you stow it away.

The keys to this table’s strength are its wide rails, rigid continuous hinges and hardwood legs. The oversize rails and long hinges prevent the table from racking. The solid-wood legs prevent the plywood end panels from bending or shaking. 

Go ahead and shove this table around the shop. The hardwood legs can take the punishment. Folded up, it stands on a durable hardwood rail, so you can slide the table across the floor into a small cubbyhole (Photo 2).

Photo 2: This table is built like a rock but knocks down in only a minute. You don’t need any tools and you don’t have to keep track of any loose pieces. Simply unscrew four knobs, fold the rails and legs on top of each other and tuck the worktable away.

Tools and Materials

This is a low-cost, easily built plywood project.Total cost is about $75, half for the wood and half for the hardware. You can build it in a day, no sweat, using little more than a tablesaw, jigsaw, hacksaw and a drill. All you have to do is cut a few plywood pieces to size, rip and cut some narrow 3/4-in.-hardwood boards to length and accurately drive in a whole mess of hinge screws. To make setting the hinges a lot easier, we recommend using a self-centering bit (see Sources). 

Build your table from one sheet of an inexpensive grade of birch plywood (about $40). Fir plywood and MDF are even less expensive, but both are inferior substitutes. Fir plywood is usually quite twisted and MDF is way too heavy. 

You’ll need some 3/4-in. solid wood for mounting the hinges. Plywood won’t do, because the hinge screws run into the edge of these boards. This would place the screws between the plies and chances are they wouldn’t hold. Pine isn’t a great choice, either, because it’s too soft to hold small screws well. Go with a hardwood that’s milled flat so you can glue its faces together. Birch or red oak are good choices.

Pick up most of the hardware at a hardware store or home center (see the Shopping List, ...

Click here to read the rest of the article from American Woodworker