American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

How to Deal with Knots Montgomery AL

A spike knot is formed when a board is cut right through the length of a branch. A spike knot may be tight at its base (the intergrown portion) and loose at its end (the encased portion).

The Home Depot
(334)272-8552
2312 Eastern Blvd
Montgomery, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

FASTENING SOLUTIONS INC
334-284-8300
3075 SELMA HWY MONTGOMERY, AL, 36108
Montgomery, AL
 
ABC Supply Co.,Inc/Montgomery
334-263-4755
520 Air Base Blvd. Montgomery, AL, 36108
Montgomery, AL
 
Fastenal- Montgomery
334-244-1989
849 Lagoon Business Loop Montgomery, AL, 36117
Montgomery, AL
 
LOWE'S OF S. MONTGOMERY, ALA.
334 409-9000
1950 EASTERN BLVD. MONTGOMERY, AL, 36117
Montgomery, AL
 
The Home Depot
(334)285-1693
2710 Legends Parkway
Prattville, AL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Montgomery
334-284-6069
4560 Newcomb Ave Montgomery, AL, 36108
Montgomery, AL
 
Lowe's
(334) 409-9000
1950 Eastern Blvd
Montgomery, AL
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Eastdale Mall
(334) 271-8200
1500 Eastdale Mall
Montgomery, AL
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18

Ace Hardware And The Feedlot
(334) 284-1788
2050 Meriwether Rd
Pike Road, AL
 

How to Deal with Knots

How to Deal with Knots



Knots are usually considered defects in wood. They're cut out of boards and thrown on a scrap heap. But take a closer look at a knot. In a hardwood, it's surrounded by stunning grain. Why not make it the focal point of your next project? The best knots crop up on some of the least expensive, lowest grade boards available. Dealing with knots can add extra work to a project, but you don't need any special equipment. You just have to know what you're up against. To begin, take a look at where the three basic types of knots come from in the photos at right.

An intergrown knot is the base of a living branch within a tree. It's surrounded by a halo of circular growth rings. An intergrown knot is also called a “tight” knot because it's tightly bound to the wood around it.

 

An intergrown knot is the base of a living branch within a tree. It's surrounded by a halo of circular growth rings. An intergrown knot is also called a “tight” knot because it's tightly bound to the wood around it.

A spike knot is formed when a board is cut right through the length of a branch. A spike knot may be tight at its base (the intergrown portion) and loose at its end (the encased portion).

 

Use knots for drama. Here's an opportunity to have fun with unusual patterns, as in this spalted-maple kitchen table. It has a comet-shaped pairing of a huge intergrown knot and a very long spike knot. Showing off the incredible swirling grain around a knot turns an inexpensive, lower grade board into a beautiful example of nature's art.

Resawing can be spectacular! A board with knots near an edge yields the most interesting mirror-image patterns, as shown in this piece of aromatic red cedar. Before you cut a board down its length on a bandsaw, hold the board on edge against a mirror. The outside of the board and its reflected image give you a pretty good idea of the book-matched pattern you'll get after resawing.

 


 

Keep your distance from knots when you're cutting them out. It's tempting to get the last inch out of every clear piece, but often it's not worth it. The wood fibers around a knot have a very steep slope. (Right next to the knot, they run almost vertically, the same direction as the branch grew on the tree.) Wood fibers with a steep slope are called “short grain.” Short grain weakens the end of a board, making it unsuitable for rails and legs. Short grain may also cause the end to chip out when you joint or plane the board.

The Way Wood Works 

Pound out an encased knot before ripping a board on the tablesaw. If a saw blade were to catch this knot, it would launch it like a missile!

Click here to read the rest of the article from American Woodworker