American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

How to Deal with Knots Norman OK

A spike knot is formed when a board is cut right through the lengthof a branch. A spike knot may be tight at its base (the intergrownportion) and loose at its end (the encased portion).

The Home Depot
(405)579-7700
850 Ed Noble Pkwy
Norman, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(405)631-9600
7400 S Shields Blvd
Oklahoma City, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Norman
405-573-2661
1100 N. Porter Ave Suite 100 Norman, OK, 73071
Norman, OK
 
LOWE'S OF NORMAN, OK
405 329-2009
2555 HEMPHILL DRIVE NORMAN, OK, 73069
Norman, OK
 
Lowe's
(405) 246-3581
1501 South I-35 Service Road
Moore, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

The Home Depot
(405)895-6064
650 SW 19th Street
Moore, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(405)737-3410
1600 S Sooner Road
Midwest City, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(405) 329-2009
2555 Hemphill Drive
Norman, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Sooner Fashion Mall
(405) 366-0800
3201 W Main St
Norman, OK
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Lowe's of Moore
405-246-3581
1501 South I-35 Service Rd Moore, OK, 73160
Moore, OK
 

How to Deal with Knots

How to Deal with Knots



Knots are usually considered defects in wood. They're cut out of boards and thrown on a scrap heap. But take a closer look at a knot. In a hardwood, it's surrounded by stunning grain. Why not make it the focal point of your next project? The best knots crop up on some of the least expensive, lowest grade boards available. Dealing with knots can add extra work to a project, but you don't need any special equipment. You just have to know what you're up against. To begin, take a look at where the three basic types of knots come from in the photos at right.

An intergrown knot is the base of a living branch within a tree.It's surrounded by a halo of circular growth rings. An intergrown knot is also called a “tight” knot because it's tightly bound to the wood around it.

An encased knot is formed when a tree grows around a dead branch. It's surrounded by a dark ring of bark, and its center is often decayed. An encased knot is also called a "loose" knot, because the bark prevents the knot from tightly binding to the wood around it.

A spike knot is formed when a board is cut right through the lengthof a branch. A spike knot may be tight at its base (the intergrown portion) and loose at its end (the encased portion).

Use knots for drama. Here's an opportunity to have fun with unusual patterns, as in this spalted-maple kitchen table. It has a comet-shaped pairing of a huge inter grown knot and a very long spike knot. Showing off the incredible swirling grain around a knot turns an inexpensive, lower grade board into a beautiful example of nature's art.

Resawing can be spectacular! A board with knots near an edge yields the most interesting mirror-image patterns, as shown in this piece of aromatic red cedar. Before you cut a board down its length on a bandsaw, hold the board on edge against a mirror. The outside of the board and its reflected image give you a pretty good idea of the book-matched pattern you'll get after resawing.

Keep your distance from knots when you're cutting them out. It'stempting to get the last inch out of every clear piece, but often it'snot worth it. The wood fibers around a knot have a very steep slope.(Right next to the knot, they run almost vertically, the same directionas the branch grew on the tree.) Wood fibers with a steep slope arecalled “short grain.” Short grain weakens the end of a board, making itunsuitable for rails and legs. Short grain may also cause the end tochip out when you joint or plane the board.

The Way Wood Works 

Pound out an encased knot before ripping a board on the tablesaw. Ifa saw blade were to catch this knot, it would launch it like a missile!The best tool to drive out a knot is a large dowel, rather than aslender metal punch. A punch can get stuck inside a decayed knot, but...

Click here to read the rest of the article from American Woodworker