American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

How to Deal with Knots Sierra Vista AZ

A spike knot is formed when a board is cut right through the length of a branch. A spike knot may be tight at its base (the intergrown portion) and loose at its end (the encased portion).

The Home Depot
(520)439-2806
3500 Avenida Cochise
Sierra Vista, AZ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Lowe's of Sierra Vista, AZ
520-439-3640
3700 Martin Luther King Parkway Sierra Vista, AZ, 85635
Sierra Vista, AZ
 
Sierra Vista Ace Hardware
(520) 458-3650
3756 E Fry Blvd, Corner of Fry Blvd & Hwy. 92
Sierra Vista, AZ
 
Foxworth Galbraith- Huachuca City
520-456-1200
698 N. Gonzales Blvd Huachuca City, AZ, 85616
Huachuca City, AZ
 
Energy Smart Concepts Inc
(520) 459-1997
www.iamenergysmart.com
Sierra Vista, AZ
 
Lowe's
(520) 439-3640
3700 Martin Luther King Parkway
Sierra Vista, AZ
Hours
M-SA 6 am - 9 pm
SU 7 am - 8 pm

The Mall Of Sierra Vista
(520) 515-3200
2250 El Mercado Loop
Sierra Vista, AZ
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Kmart 3695 / Cross Merch
(520) 459-0345
2011 E Fry Blvd
Sierra Vista, AZ
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

B & D Lumber And Hardware
(520) 432-4272
93 Bisbee Road
Bisbee, AZ
 
Mountain View Air Conditioning & Heating, LLC
(520) 226-4299
3410 E. Canyon De Flores
Sierra Vista, AZ
Services Offered
HVAC Contractor, Heating contractor

How to Deal with Knots

How to Deal with Knots



Knots are usually considered defects in wood. They're cut out of boards and thrown on a scrap heap. But take a closer look at a knot. In a hardwood, it's surrounded by stunning grain. Why not make it the focal point of your next project? The best knots crop up on some of the least expensive, lowest grade boards available. Dealing with knots can add extra work to a project, but you don't need any special equipment. You just have to know what you're up against. To begin, take a look at where the three basic types of knots come from in the photos at right.

An intergrown knot is the base of a living branch within a tree. It's surrounded by a halo of circular growth rings. An intergrown knot is also called a “tight” knot because it's tightly bound to the wood around it.

 

An intergrown knot is the base of a living branch within a tree. It's surrounded by a halo of circular growth rings. An intergrown knot is also called a “tight” knot because it's tightly bound to the wood around it.

A spike knot is formed when a board is cut right through the length of a branch. A spike knot may be tight at its base (the intergrown portion) and loose at its end (the encased portion).

 

Use knots for drama. Here's an opportunity to have fun with unusual patterns, as in this spalted-maple kitchen table. It has a comet-shaped pairing of a huge intergrown knot and a very long spike knot. Showing off the incredible swirling grain around a knot turns an inexpensive, lower grade board into a beautiful example of nature's art.

Resawing can be spectacular! A board with knots near an edge yields the most interesting mirror-image patterns, as shown in this piece of aromatic red cedar. Before you cut a board down its length on a bandsaw, hold the board on edge against a mirror. The outside of the board and its reflected image give you a pretty good idea of the book-matched pattern you'll get after resawing.

 


 

Keep your distance from knots when you're cutting them out. It's tempting to get the last inch out of every clear piece, but often it's not worth it. The wood fibers around a knot have a very steep slope. (Right next to the knot, they run almost vertically, the same direction as the branch grew on the tree.) Wood fibers with a steep slope are called “short grain.” Short grain weakens the end of a board, making it unsuitable for rails and legs. Short grain may also cause the end to chip out when you joint or plane the board.

The Way Wood Works 

Pound out an encased knot before ripping a board on the tablesaw. If a saw blade were to catch this knot, it would launch it like a missile!

Click here to read the rest of the article from American Woodworker