American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

How to Hang Inset Doors Charlotte NC

Round out your door-installing arsenal with a pair of secret weapons—a plastic laminate sample swiped from the home center and a double-bearing flush-trim router bit. This great new bit should be a fixture in every woodworking shop.

The Home Depot
(704)365-1291
1220 N Wendover Rd
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)596-1550
8135 University Cty Blvd
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)544-2877
10210 Centrum Pkwy
Pineville, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)845-9200
1837 Matthews Twnsp Pkwy
Matthews, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)535-6982
9501 Albemarle Rd
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)522-8383
4750 South Boulevard
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)504-9836
14310 Rivergate Pkwy
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Matthews, NC
(704) 847-8300
1725 Windsor Square Drive
Matthews, NC

Data Provided by:
The Home Depot
(704)814-6131
5415 Ballantyne Cmmns Pk
Charlotte, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(704)865-9532
2870 E Franklin Blvd
Gastonia, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

How to Hang Inset Doors

How to Hang Inset Doors

Install butt hinges perfectly and establish consistent, slender margins.

by Tim Johnson

Nothing signals skillful craftsmanship like an inset door with elegant hinges and eye-pleasing margins. This challenging job leaves no room for error: Uneven surfaces and unsightly gaps will tell the tale if the hinges, door and frame don’t fit precisely. Like mastering hand-cut dovetails, successfully hanging inset doors on mortised butt hinges is a woodworking milestone. 

I’ll show you a three-step method for installing inset doors that produces great results every time. First, you match the door to the opening. Then you rout mortises for the hinges. And finally, you create uniform, attractive margins between the door and frame. Of course, you can skip the mortising step altogether by choosing different hinges (see “No-Mortise Hinge Options, below”).

To complete the job, you’ll need a couple simple jigs, a mortising bit, and a laminate trimmer. A laminate trimmer is a compact router that’s a really handy addition to any woodworking shop. (If you don’t own a laminate trimmer, this is a great excuse to buy one.) 

Round out your door-installing arsenal with a pair of secret weapons—a plastic laminate sample swiped from the home center and a double-bearing flush-trim router bit. This great new bit should be a fixture in every woodworking shop.

Choose Hinges

Your first task is to choose between extruded (also referred to as drawn or cast) or stamped hinges (see photos, above). Extruded hinges are machined and drilled, so there’s virtually no play between the knuckles or around the hinge pin. Stamped hinges are made from thinner stock. Their leaves are bent to form the knuckles that surround the pin. Extruded hinges will last longer, because their knuckles have more bearing surface.

I often use stamped hinges because they cost about one-third as much as extruded hinges and they’re available at most hardware stores. They work fine in most situations. Examine stamped hinges carefully before buying. If you notice large gaps between the knuckles and vertical play between the two hinge leaves, keep looking. Be aware that some stamped hinges are brass plated rather than solid brass. Hinges with loose pins make it easy to remove and reinstall the door, but they aren’t widely available.

Before you install the hinges, make sure the screws’ heads recess fully in the chamfered holes in the hinge leaves. Amazingly, the brass screws supplied with brass hinges often don’t fit. If that’s the case, you’ll have to deepen the screw-hole chamfers or use smaller screws. 

Brass screws are delicate. The heads strip easily or break off, leaving the shaft buried in the wood. Avoid trouble with broken brass screws by threading the pilot holes with steel screws, which are much more durable. Install the brass screws only once, after the ...

Click here to read the rest of the article from American Woodworker