American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Instant Wheel-Dresser Support Claremore OK

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Claremore
918-342-4548
1614 North Lynn Riggs Blvd Claremore, OK, 74017
Claremore, OK
 
Pixley Lumber Co
(918) 341-4223
715 W Will Rogers
Claremore, OK
 
Cribbets True Value
(918) 371-3306
1008 Main St
Collinsville, OK
 
LOWE'S OF OWASSO, OK
918 274-0881
12001 E. 96TH STREET NORTH OWASSO, OK, 74055
Owasso, OK
 
Westlake Ace Hardware
(918) 343-3117
810 N Lynn Riggs Blvd
Claremore, OK
 
Lowe's
(918) 923-1030
1746 South Lynn Riggs Boulevard
Claremore, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

Claremore - Auth Hometown
(918) 343-2500
1648 North Lynn Riggs Blvd
Claremore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20

Lowe's
(918) 274-0881
12001 E. 96Th Street North
Owasso, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Pryor Lumber
(918) 825-2260
1031 West Highway 20
Pryor, OK
 

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker