American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Instant Wheel-Dresser Support East Wenatchee WA

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(509)663-5505
1405 Maiden Lane
Wenatchee, WA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Wenatchee Valley Mall
(509) 886-1200
611 Valley Mall Pkwy
E Wenatchee, WA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Lowe's
(509) 663-4530
1200 Walla Walla Avenue
Wenatchee, WA
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Clifford's Hardware
(509) 782-1877
127 Cottage Ave
Cashmere, WA
 
The Home Depot
(360)533-6661
2213 Port Industrial Rd
Aberdeen, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

AG Supply Ace Hardware
(509) 884-6647
220 Grant Rd
East Wenatchee, WA
 
LOWE'S OF WENATCHEE, WA.
509 663-4530
1200 WALLA WALLA AVENUE WENATCHEE, WA, 98801
Wenatchee, WA
 
Stan's Merry Mart Inc
(509) 662-5858
733 S Wenatchee Ave
Wenatchee, WA
 
The Home Depot
(425)451-7351
325 120th Ave NE
Bellevue, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(509)534-8588
5617 E Sprague Ave
Spokane Valley, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker