American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Instant Wheel-Dresser Support Layton UT

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(801)543-2296
449 N. Main St
Layton, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(801)292-0238
50 N Market Place Dr
Centerville, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Ace Hardware
(801) 546-2689
135 W 320 N
Kaysville, UT
 
Ace Hdwe Wyndom Square
(801) 771-2300
1330 E Highway 193 # C-3, 1.5 Miles east of Hill AFB South Gate
Layton, UT
 
Kmart 7426 / Cross Merch
(801) 776-4181
2010 N Main St
Layton, UT
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

The Home Depot
(801)621-7373
999 W Riverdale Road
Riverdale, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(801)393-0106
984 Wall Avenue
Ogden, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

LOWE'S OF LAYTON, UT.
801 776-4447
1055 W. ANTELOPE DRIVE LAYTON, UT, 84041
Layton, UT
 
Lowe's
(801) 776-4447
1055 W. Antelope Drive
Layton, UT
Hours
M-SA 6 am - 10 pm
SU 8 am - 9 pm

Lowe's
(801) 820-1060
1986 North 2000 West
Clinton, UT
Hours
M-SA 6 am - 10 pm
SU 8 am - 9 pm

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker