American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Instant Wheel-Dresser Support Lebanon TN

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(615)444-5472
955 S Hartman Drive
Lebanon, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)824-2391
205 N Anderson Lane
Hendersonville, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(615) 547-7236
634 South Cumberland Street
Lebanon, TN
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF LEBANON, TN
615 547-7236
634 SOUTH CUMBERLAND STREET LEBANON, TN, 37087
Lebanon, TN
 
ACE Hardware of Mt. Juliet
(615) 773-9223
4110 N Mt Juliet Rd, In the old skate center
Mount Juliet, TN
 
The Home Depot
(615)889-7211
5010 Old Hickory Blvd
Hermitage, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(615)220-5044
551 President Place
Smyrna, TN
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Lebanon
615-443-7612
604 E Main St Lebanon, TN, 37087
Lebanon, TN
 
Lowe's
(615) 773-6370
300 Pleasant Grove Rd, Suite 200
Mt. Juliet, TN
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Lowe's of Mt. Juliet
615-773-6370
300 Pleasant Grove Rd Suite 200 Mt. Juliet, TN, 37122
Mt. Juliet, TN
 

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker