American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Instant Wheel-Dresser Support Mansfield TX

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(817)453-4038
1725 N US Hwy 287
Mansfield, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #27
(817) 417-0070
4624 South Cooper St.
Arlington, TX

Data Provided by:
The Home Depot
(972)602-9385
5280 South Hwy 360
Grand Prairie, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)496-3212
1151 Bridgewood Dr
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)293-0343
7950 I-35 W South Fwy
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)468-4224
4611 S Cooper St
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)447-6602
300 NW John Jones
Burleson, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(972)299-9390
373 E Fm 1382
Cedar Hill, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)459-4300
201 Rd To Six Flags West
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Brazos Forest Products - Grand Prairie
(972) 602-1225
2760 N Great SW Parkway
Grand Prairie, TX

Data Provided by:
Data Provided by:

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker