American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Instant Wheel-Dresser Support North Brunswick NJ

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(732)438-5980
4095 US Route 1
Monmouth Junction, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)987-8686
701 Nassau Park Blvd
Princeton, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(908)222-7700
1515 Route 22
Watchung, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)585-0411
750 Highway Rt 130
Robbinsville, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Willard Brothers Lumber
(800) 320-6519
300 Basin Road
Trenton, NJ

Data Provided by:
AGINCOURT
(908) 874-8234
212 E Mountain Rd
Hillsborough, NJ

Data Provided by:
The Home Depot
(908)252-0101
736 Route 202 South
Bridgewater, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)426-2441
739 Route 33 West
E Windsor, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)393-3697
1621 N Olden Avenue
Ewing, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(908)782-2577
244 Highway 202
Flemington, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details