American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Instant Wheel-Dresser Support Rome GA

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(706)236-9030
103 Hicks Drive
Rome, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(770)606-0298
100 Gentil Street
Cartersville, GA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Rome
706-802-0270
110 East Eighth Ave Rome, GA, 30161
Rome, GA
 
Cave Spring Hardware
(706) 777-3910
14 Mill Street
Cave Spring, GA
 
Lavender Mountain Do it Best
(706) 295-0299
4065 Martha Berry Hwy Nw
Rome, GA
 
The Home Depot
(678)246-0107
1500 Rome Highway
Cedartown, GA
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

Ace Hardware Of East Rome Inc
(706) 291-1939
1804 Turner Mccall Blvd SW
Rome, GA
 
Kmart 4719 / Cross Merch
(706) 236-9880
102 Hicks Drive
Rome, GA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Mathis Building Supply
(706) 291-1240
22 Shorter Avenue
Rome, GA
 
Lowe's
(706) 232-6877
2338 Shorter Avenue N.W.
Rome, GA
Hours
M-SA 7 am - 10 pm
SU 8 am - 7 pm

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker