American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » ยป

Instant Wheel-Dresser Support Twinsburg OH

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support.

The Home Depot
(330)908-1300
8211 Macedonia Commons
Macedonia, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Cleveland, OH
(440) 232-7979
22745 Rockside Road
Bedford, OH

Data Provided by:
The Home Depot
(216)581-6611
21000 Libby Rd
Maple Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)297-1303
3460 Mayfield Rd
Cleveland Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)741-6123
3355 Steelyard Drive
Cleveland, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)562-6000
18800 N Market Pl Drive
Aurora, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)422-0401
9585 State Route 14
Streetsboro, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)922-3448
325 Howe Ave
Cuyahoga Falls, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(440)895-4420
21669 Center Ridge Rd
Rocky River, OH
Hours
Mon-Thur: 7:00am-9:00pm
Fri-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)670-0988
4066 Medina Rd
Fairlawn, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Instant Wheel-Dresser Support

Instant Wheel-Dresser Support

I use my grinder almost exclusively for beveling my chisels, so I like to keep the tool rest set to produce the 25-degree bevel I prefer. Having to reset the angle after using my diamond wheel dresser to clean and flatten the wheel bothered me until I made this wedge-shaped support. Like many of my friends, I've upgraded my grinder by installing a top-quality tool rest (see Source, below). The wedge-shaped support I made fits snugly in the tool rest and instantly positions my diamond dresser correctly, perpendicular to the wheel's face.

After drawing the support's profile on the end of a 12-in.-long, 1-1/4-in. x 1-3/4-in. blank, I headed to my tablesaw. First, I cut a rabbet on the back of the blank to create the tongue. Rather than going for a precise fit, I cut the tongue a bit narrow and planned to install adjustment screws later.

Next, I cut the bevel. Its angle depends on your preferred bevel angle, the size of your grinding wheel and the location of your tool rest relative to the wheel. After checking to make sure the bevel's angle was correct, I cut the support from the blank and installed the adjustment screws. Now, switching from grinding to dressing is effortless.

Source
Lee Valley Tools, (800) 871-8158, www.leevalley.com
Veritas tool rest, #05M23.01, $40.

Click here to read the rest of the article from American Woodworker